CCAMP Working Group                                      S. Belotti, Ed.
Internet-Draft                                                     Nokia
Obsoletes: 9093 (if approved)                               I. Busi, Ed.
Intended status: Standards Track                                  Huawei
Expires: 7 June 2025                                      D. Beller, Ed.
                                                                   Nokia
                                                            E. Le Rouzic
                                                                  Orange
                                                                  A. Guo
                                                  Futurewei Technologies
                                                         4 December 2024


              Common YANG Data Types for Layer 0 Networks
                    draft-ietf-ccamp-rfc9093-bis-12

Abstract

   This document defines a collection of common data types, identities,
   and groupings in the YANG data modeling language.  These common types
   and groupings, derived from the built-in YANG data types, identities,
   and groupings are intended to be imported by modules that model Layer
   0 configuration and state capabilities, such as Wavelength Switched
   Optical Networks (WSONs) and flexi-grid Dense Wavelength Division
   Multiplexing (DWDM) networks.

   This document obsoletes RFC 9093 by replacing the YANG module it
   contained with a new revision that includes additional YANG data
   types, identities and groupings.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at https://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on 7 June 2025.





Belotti, et al.            Expires 7 June 2025                  [Page 1]

Internet-Draft            L0 Common YANG Types             December 2024


Copyright Notice

   Copyright (c) 2024 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents (https://trustee.ietf.org/
   license-info) in effect on the date of publication of this document.
   Please review these documents carefully, as they describe your rights
   and restrictions with respect to this document.  Code Components
   extracted from this document must include Revised BSD License text as
   described in Section 4.e of the Trust Legal Provisions and are
   provided without warranty as described in the Revised BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   2
     1.1.  Terminology and Notations . . . . . . . . . . . . . . . .   3
     1.2.  Prefix in Data Node Names . . . . . . . . . . . . . . . .   3
   2.  Layer 0 Types Module Contents . . . . . . . . . . . . . . . .   4
     2.1.  WDM Label and Label Range . . . . . . . . . . . . . . . .   8
   3.  YANG Module for Layer 0 Types . . . . . . . . . . . . . . . .  10
   4.  Security Considerations . . . . . . . . . . . . . . . . . . .  57
   5.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  58
   6.  References  . . . . . . . . . . . . . . . . . . . . . . . . .  58
     6.1.  Normative References  . . . . . . . . . . . . . . . . . .  58
     6.2.  Informative References  . . . . . . . . . . . . . . . . .  62
   Appendix A.  The Complete Schema Trees  . . . . . . . . . . . . .  63
   Appendix B.  Changes from RFC 9093  . . . . . . . . . . . . . . .  69
   Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . .  73
   Contributors  . . . . . . . . . . . . . . . . . . . . . . . . . .  73
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  74

1.  Introduction

   YANG [RFC7950] is a data modeling language used to model
   configuration data, state data, Remote Procedure Calls, and
   notifications for network management protocols such as the Network
   Configuration Protocol (NETCONF) [RFC6241].  The YANG language
   supports a small set of built-in data types and provides mechanisms
   to derive other types from the built-in types.

   This document introduces a collection of common data types derived
   from the built-in YANG data types.  The derived types and groupings
   are designed to be the common types applicable for modeling Traffic
   Engineering (TE) features as well as non-TE features (e.g., physical
   network configuration aspects) for Layer 0 optical networks in
   model(s) defined outside of this document.  The applicability of



Belotti, et al.            Expires 7 June 2025                  [Page 2]

Internet-Draft            L0 Common YANG Types             December 2024


   Layer 0 types specified in this document includes Wavelength Switched
   Optical Networks (WSONs) [RFC6163] [ITU-T_G.694.1] and
   [ITU-T_G.694.2], and flexi-grid Dense Wavelength Division
   Multiplexing (DWDM) networks [RFC7698] [ITU-T_G.694.1].

   This document adds new type definitions to the YANG modules and
   obsoletes [RFC9093].  For further details, see the revision
   statements of the YANG module in Section 3 or the summary in
   Appendix B.

   This document obsoletes [RFC9093] by replacing it in its entirety.
   It provides a new revision of the YANG module contained in that RFC,
   and retains the data types previously defined, but also adds new type
   definitions to the YANG module.  For further details, see Appendix B.

   The YANG data model in this document conforms to the Network
   Management Datastore Architecture defined in [RFC8342].

1.1.  Terminology and Notations

   Refer to [RFC7446] and [RFC7581] for the key terms used in this
   document, and the terminology for describing YANG data models can be
   found in [RFC7950].

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in
   BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
   capitals, as shown here.

1.2.  Prefix in Data Node Names

   In this document, names of data nodes and other data model objects
   are prefixed using the standard prefix associated with the
   corresponding YANG imported module.

               +==========+===================+===========+
               | Prefix   | YANG module       | Reference |
               +==========+===================+===========+
               | te-types | ietf-te-types     | [RFCYYYY] |
               +----------+-------------------+-----------+
               | l0-types | ietf-layer0-types | RFC XXXX  |
               +----------+-------------------+-----------+

                 Table 1: Prefixes and corresponding YANG
                                  module





Belotti, et al.            Expires 7 June 2025                  [Page 3]

Internet-Draft            L0 Common YANG Types             December 2024


      RFC Editor Note: Please replace XXXX with the RFC number assigned
      to this document.  Please replace YYYY with the RFC number
      assigned to [I-D.ietf-teas-rfc8776-update].  Please remove this
      note.

2.  Layer 0 Types Module Contents

   This document defines a YANG module for common Layer 0 types, ietf-
   layer0-types.  This module is used for WSON and flexi-grid DWDM
   networks.  The "ietf-layer0-types" module contains the following YANG
   reusable YANG data types, identities and groupings:

   l0-grid-type:  A base YANG identity for the grid type as defined in
      [RFC6205] and [RFC7699].

   cwdm-ch-spc-type:  A base YANG identity for the Coarse Wavelength
      Division Multiplexing (CWDM) channel-spacing type as defined in
      [RFC6205].

   dwdm-ch-spc-type:  A base YANG identity for the DWDM channel-spacing
      type as defined in [RFC6205].

   flexi-ncfg-type:  A base YANG identity for the DWDM flexi-grid
      Nominal Central Frequency Granularity (NCFG) type as defined in
      [RFC7699].

      Note that the only value for NCFG standardized in [ITU-T_G.694.1]
      is 6.25GHz.

   flexi-slot-width-granularity:  A base YANG identity for the DWDM
      flexi-grid Slot Width Granularity (SWG) type, as defined in
      [RFC7699].

      Note that the only value for SWG standardized in [ITU-T_G.694.1]
      is 12.5GHz.

   fec-type:  A base YANG identity from which specific FEC (Forward
      Error Correction) type identities are derived.

   line-coding:  A base YANG identity from which specific identities
      defining the bit rate/line coding of optical tributary signals are
      derived.

   wavelength-assignment:  A base YANG identity from which for
      Wavelength selection method, as defined in [RFC7689].

   operational-mode:  A YANG data type used to identify an organization




Belotti, et al.            Expires 7 June 2025                  [Page 4]

Internet-Draft            L0 Common YANG Types             December 2024


      (e.g., vendor) specific mode for transceiver capability
      description, as defined in Section 2.5.2 of
      [I-D.ietf-ccamp-optical-impairment-topology-yang]

   wson-label-start-end:  The WSON label range was defined in [RFC6205],
      and the generic topology model defines the label-start/label-end
      in [RFC8795].  This grouping shows the WSON-specific label-start
      and label-end information.  See Section 2.1 for more details.

   wson-label-hop:  The WSON label range was defined in [RFC6205], and
      the generic topology model defines the label-hop in [RFC8795].
      This grouping shows the WSON-specific label-hop information.  See
      Section 2.1 for more details.

   l0-label-range-info:  A YANG grouping that defines the Layer 0 label
      range information applicable for WSON as defined in [RFC6205].
      The label range info is defined per priority [RFC4203].

      This grouping is used in the flexi-grid DWDM by adding more flexi-
      grid-specific parameters.  See Section 2.1 for more details.

   wson-label-step:  A YANG grouping that defines label steps for WSON
      as defined in [I-D.ietf-teas-rfc8776-update].  See Section 2.1 for
      more details.

   flexi-grid-label-start-end:  The flexi-grid label range was defined
      in [RFC7699], and the generic topology model defines the label-
      start/label-end in [RFC8795].

      This grouping shows the flexi-grid-specific label- start and
      label-end information which is used to describe the range of
      available nominal central frequencies.  See Section 2.1 for more
      details.

      As described in section 3.1 of [RFC8363], the range of available
      nominal central frequencies are advertised for m=1, which means
      that for an available central frequency n, the frequency slot from
      central frequency n-1 to central frequency n+1 is available.

   flexi-grid-label-hop:  The flexi-grid label range was defined in
      [RFC8363], and the generic topology model defines the label-hop in
      [RFC8795].

      This grouping shows the WSON-specific label-hop information.  See
      Section 2.1 for more details.

   flexi-grid-label-range-info:  A YANG grouping that defines flexi-grid




Belotti, et al.            Expires 7 June 2025                  [Page 5]

Internet-Draft            L0 Common YANG Types             December 2024


      label range information as defined in [RFC8363].  See Section 2.1
      for more details.  See Section 2.1 for more details.

   flexi-grid-label-step:  A YANG grouping that defines flexi-grid label
      steps as defined in [I-D.ietf-teas-rfc8776-update].  See
      Section 2.1 for more details.

   wdm-label-start-end:  A YANG grouping that combines the definition of
      label-start/label-end information that was defined separately in
      wson-label-start-end and flexi-grid-label-start-end, to support
      optical network scenarios that contain both fixed- and flexi-grid
      links.  See Section 2.1 for more details.

   wdm-label-hop:  A YANG grouping that combines the definition of label
      hop information that was defined separately in wson-label-hop and
      flexi-grid-label-hop, to support optical network scenarios that
      contain both fixed- and flexi-grid links.  See Section 2.1 for
      more details.

   wdm-label-range-info:  A YANG grouping that combines the definition
      of label range information that was defined separately in wson-
      label-range-info and flexi-grid-label-range-info, to support
      optical network scenarios that contain both fixed- and flexi-grid
      links.  See Section 2.1 for more details.

   wdm-label-step:  A YANG grouping that combines the definition of
      label step information defined separately in wson-label-step and
      flexi-grid-label-step, to support optical network scenarios that
      contain both fixed- and flexi-grid links.  See Section 2.1 for
      more details.

   transceiver-capabilities:  A YANG grouping to define the transceiver
      capabilities (also called "modes") needed to determine optical
      signal compatibility.

   standard-mode:  A YANG grouping for the standard modes defined in
      [ITU-T_G.698.2].

   organizational-mode:  A YANG grouping to define transponder
      operational mode supported by organizations or vendors, as defined
      in [I-D.ietf-ccamp-optical-impairment-topology-yang].

   explicit-mode:  A YANG grouping to define the list of attributes
      related to optical impairments limits in case of transceiver
      explicit mode, as defined in
      [I-D.ietf-ccamp-optical-impairment-topology-yang].

      Note that the the actual portion of the spectrum occupied by an



Belotti, et al.            Expires 7 June 2025                  [Page 6]

Internet-Draft            L0 Common YANG Types             December 2024


      OTSi is not explicitly reported within the explicit-mode
      parameters because it can be calculated using the available-baud-
      rate, the roll-off and the min-carrier-spacing attributes.

   transmitter-tuning-range:  A YANG grouping that defines the
      transmitter tuning range, which includes the minimum and maximum
      tuning frequency, as well as the frequency tuning steps.

   common-organizational-explicit-mode:  A YANG grouping to define the
      common capabilities attributes limit range in case of operational
      mode and explicit mode.

   modulation:  A base YANG identity to define the different modulation
      types, as defined in [ITU-T_G.Sup39]

   snr:  A YANG data type used to represent an (Optical) Signal to Noise
      Ratio measured over 0.1 nm resolution bandwidth, as defined in
      [ITU-T_G.977.1]

   psd:  A YANG data type used to represent a Power Spectral Density
      (PSD), as defined in [ITU-T_G.9700]

   penalty-value:  A YANG grouping to define the penalty value for
      multiple penalty types, such as Chromatic Dispersion (CD),
      Polarization Mode Dispersion (PMD), as defined in [ITU-T_G.666] or
      Polarization Dependent Loss(PDL)

   switching-wson-lsc:  A YANG identity for the Wavelength Switched
      Optical Network Lambda-Switch Capable (WSON-LSC) interface
      switching capability as defined in [RFC7688].

   switching-flexi-grid-lsc:  A YANG identity for the Flexi-Grid Lambda-
      Switch Capable (Flexi-Grid-LSC) interface switching capability as
      defined in [RFC8363].

   It is worth noting that there is an inheritance relationship between
   the Lambda-Switch Capable (LSC) switching capability, defined in
   [RFC3471], and the WSON-LSC and Flexi-Grid-LSC, defined respectively
   in [RFC7688] and [RFC8363].  As a consequence, the 'switching-wson-
   lsc' and 'switching-flexi-grid-lsc' YANG identities are defined as
   derived identities from the 'switching-lsc', defined in
   [I-D.ietf-teas-rfc8776-update].









Belotti, et al.            Expires 7 June 2025                  [Page 7]

Internet-Draft            L0 Common YANG Types             December 2024


2.1.  WDM Label and Label Range

   As described in [RFC6205] and [RFC7699], the WDM label represents the
   frequency slot assigned to a WDM Label Switched Path (LSP) on a given
   WDM Link, which models an Optical Multiplex Section (OMS) Media
   Channel Group (MCG) as described in
   [I-D.ietf-ccamp-optical-impairment-topology-yang].

   The same WDM label shall be assigned to the same WDM LSP on all the
   WDM Links on a regen-free LSP path or path segment.

   A frequency slot is defined in [ITU-T_G.694.1] as a contiguous
   frequency range characterized by its nominal central frequency and
   slot width.  The frequency range allocated to a frequency slot is
   unavailable to other frequency slots.

   The definition of the frequency slot depends on the WDM grid type:

   *  In case of CWDM fixed-grid, defined in [ITU-T_G.694.2], the
      frequency slot is defined by a fixed CWDM channel spacing (cwdm-
      ch-spc-type) and by the nominal central wavelength which is
      computed as described in [RFC6205].  The formula in [RFC6205] is
      copied here for reader convenience:

         lambda = 1471 nm + n * channel spacing (measured in nm)

      where 'n' is defined in [RFC6205] as integer (positive, negative,
      or 0)

   *  In case of DWDM fixed-grid, defined in [ITU-T_G.694.1], the
      frequency slot is defined by a fixed DWDM channel spacing (dwdm-
      ch-spc-type) and by the nominal central frequency, which is
      computed as described in [RFC6205].  The formula in [RFC6205] is
      copied here for reader convenience:

         f = 193100.000 GHz + n * channel spacing (measured in GHz)

      where 'n' is defined in [RFC6205] as integer (positive, negative,
      or 0)

   *  In case of DWDM flexible-grid, defined in [ITU-T_G.694.1], the
      frequency slot is defined by the slot width and by the nominal
      central frequency, which are computed, based on the slot width
      granularity (SWG, fixed at 12.5GHz in [ITU-T_G.694.1]), and of the
      nominal central frequency granularity (NCFG, fixed at 6.25GHz in
      [ITU-T_G.694.1]) respectively, as described in [RFC7698] and
      [RFC7699].  The formulas in [RFC7699] can be generalized as
      follows:



Belotti, et al.            Expires 7 June 2025                  [Page 8]

Internet-Draft            L0 Common YANG Types             December 2024


         SW = m * SWG (measured in GHz)
         f = 193100.000 GHz + N * NCFG (measured in GHz)

      where 'n' is defined in [RFC7699] as integer (positive, negative,
      or 0) and 'm' is defined in [RFC7698] as an integer greater than
      or equal to 1.

   The definition of the channel spacing, NCFG and SWG in the YANG model
   have been generalized to support modelling of vendor-specific values
   (e.g., finer vendor-specific granularity for NCFG and SWG).

   The WDM Label Range represents the frequency slots that are available
   for WDM LSPs to be set up over a given WDM Link.

   The WDM Label Range is defined by augmenting the label-restriction
   list, defined in [I-D.ietf-teas-rfc8776-update], with WDM technology-
   specific attributes, using the l0-label-range-info grouping (for WSON
   only models) or the flexi-grid-label-range-info grouping (for DWDM
   flexible-grid only models) or the wdm-label-range-info grouping (for
   models that supports both WSON and DWDM flexible-grid).

   Each entry in the label-restriction list represents either the range
   of the available central wavelength values (in case of CWDM fixed-
   grid) or the range of the available nominal central frequencies
   values (in case of DWDM fixed or flexible grids): the grid-type
   attribute defines the type of grid for each entry of the list.

   In case of DWDM flexible grid, each entry in the label-restriction
   list represents also the range of the supported slot width values
   based on the following attributes, defined based on concepts used in
   [RFC7699]:

   *  slot-width-granularity, which represents the minimum space between
      slot widths;

   *  min-slot-width-factor: a multiplier of the slot width granularity,
      indicating the minimum slot width supported by each entry in the
      label-restriction list;

   *  max-slot-width-factor: a multiplier of the slot width granularity,
      indicating the maximum slot width supported by each entry in the
      label-restriction list.

   Each entry of the label-restriction list, as defined in
   [I-D.ietf-teas-rfc8776-update], defines a label-start, a label-end, a
   label-step and a range-bitmap.





Belotti, et al.            Expires 7 June 2025                  [Page 9]

Internet-Draft            L0 Common YANG Types             December 2024


   The label-start and label-end definitions, when used for representing
   WDM labe range, are augmented with WDM technology-specific
   attributes, using the wson-label-start-end grouping (for WSON only
   models) or the flexi-grid-label-start-end grouping (for DWDM
   flexible-grid only models) or the wdm-label-start-end grouping (for
   models that supports both WSON and DWDM flexible-grid).

   The label-step definition, when used for representing WDM labe range,
   are augmented with WDM technology-specific attributes, using the
   wson-label-step grouping (for WSON only models) or the flexi-grid-
   label-step grouping (for DWDM flexible-grid only models) or the wdm-
   label-step grouping (for models that supports both WSON and DWDM
   flexible-grid).  The label-step definition for WDM depends on the WDM
   grid type:

   *  For CWDM and DWDM fixed grids, it describes the channel spacing,
      as defined in [RFC6205];

   *  For DWDM flexible grids, it describes the nominal central
      frequency granularity (e.g., 6,25 GHz) as well as the multiplier
      for the supported values of n, as defined in [RFC7699].

3.  YANG Module for Layer 0 Types

   This YANG module references [RFC6205], [RFC7689], [RFC7699],
   [RFC7698], [RFC8363], [RFC8363], [RFC9093], [ITU-T_G.666],
   [ITU-T_G.694.1], [ITU-T_G.694.2], [ITU-T_G.698.2], [ITU-T_G.709],
   [ITU-T_G.709.2], [ITU-T_G.709.3], [ITU-T_G.959.1] [ITU-T_G.975],
   [ITU-T_G.975.1], [ITU-T_G.977.1], [ITU-T_G.9700] and [OIF_400ZR].

   <CODE BEGINS> file "ietf-layer0-types@2024-11-27.yang"
   module ietf-layer0-types {
     yang-version 1.1;
     namespace "urn:ietf:params:xml:ns:yang:ietf-layer0-types";
     prefix l0-types;

     import ietf-te-types {
       prefix te-types;
       reference
         "RFC YYYY: Common YANG Data Types for Traffic Engineering";
     }
     // RFC Editor: replace YYYY with actual RFC number assigned to
     // [I-D.ietf-teas-rfc8776-update] and remove this note

     organization
       "IETF CCAMP Working Group";
     contact
       "WG Web:  <https://datatracker.ietf.org/wg/ccamp/>



Belotti, et al.            Expires 7 June 2025                 [Page 10]

Internet-Draft            L0 Common YANG Types             December 2024


        WG List: <mailto:ccamp@ietf.org>

        Editor:  Dieter Beller
                 <mailto:Dieter.Beller@nokia.com>

        Editor:  Sergio Belotti
                 <mailto:Sergio.Belotti@nokia.com>

        Editor:  Italo Busi
                 <mailto:Italo.Busi@huawei.com>

        Editor:  Haomian Zheng
                 <mailto:zhenghaomian@huawei.com>";
     description
       "This module defines Optical Layer 0 types.  This module
        provides groupings that can be applicable to Layer 0
        Fixed Optical Networks (e.g., CWDM (Coarse Wavelength
        Division Multiplexing) and DWDM (Dense Wavelength Division
        Multiplexing)) and flexi-grid optical networks.

        Copyright (c) 2024 IETF Trust and the persons identified
        as authors of the code.  All rights reserved.

        Redistribution and use in source and binary forms, with
        or without modification, is permitted pursuant to, and
        subject to the license terms contained in, the Revised
        BSD License set forth in Section 4.c of the IETF Trust's
        Legal Provisions Relating to IETF Documents
        (https://trustee.ietf.org/license-info).

        This version of this YANG module is part of RFC XXXX; see
        the RFC itself for full legal notices.

        The key words 'MUST', 'MUST NOT', 'REQUIRED', 'SHALL', 'SHALL
        NOT', 'SHOULD', 'SHOULD NOT', 'RECOMMENDED', 'NOT RECOMMENDED',
        'MAY', and 'OPTIONAL' in this document are to be interpreted as
        described in BCP 14 (RFC 2119) (RFC 8174) when, and only when,
        they appear in all capitals, as shown here.";

   // RFC Ed.: replace XXXX with actual RFC number and remove
   // this note

   // replace the revision date with the module publication date
   // the format is (year-month-day)
     revision 2024-11-27 {
       description
         "To be updated";
       reference



Belotti, et al.            Expires 7 June 2025                 [Page 11]

Internet-Draft            L0 Common YANG Types             December 2024


         "RFC XXXX: A YANG Data Model for Layer 0 Types";
     }

     revision 2021-08-13 {
       description
         "Initial version";
       reference
         "RFC 9093: A YANG Data Model for Layer 0 Types";
     }

   /*
    * Identities
    */

     identity l0-grid-type {
       description
         "Layer 0 grid type";
       reference
         "RFC 6205: Generalized Labels for Lambda-Switch-Capable
         (LSC), Label Switching Routers,

          ITU-T G.694.2 (12/2003): Spectral grids for WDM applications:
          CWDM wavelength grid";
     }

       identity wson-grid-cwdm {
         base l0-grid-type;
         description
           "CWDM grid";
         reference
           "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC)
           Label Switching Routers,

           ITU-T G.694.2 (12/2003): Spectral grids for WDM applications:
           CWDM wavelength grid";
       }

       identity wson-grid-dwdm {
         base l0-grid-type;
         description
           "DWDM grid";
         reference
           "RFC 6205: Generalized Labels for Lambda-Switch-Capable
           (LSC), Label Switching Routers,

           ITU-T G.694.1 (10/2020): Spectral grids for WDM applications:
           DWDM frequency grid";
       }



Belotti, et al.            Expires 7 June 2025                 [Page 12]

Internet-Draft            L0 Common YANG Types             December 2024


       identity flexi-grid-dwdm {
         base l0-grid-type;
         description
           "Flexi-grid";
         reference
           "RFC 7699: Generalized Labels for the Flexi-Grid in Lambda
           Switch Capable (LSC) Label Switching Routers,

           ITU-T G.694.1 (10/2020): Spectral grids for WDM applications:
           DWDM frequency grid";
       }

     identity cwdm-ch-spc-type {
       description
         "CWDM channel-spacing type";
       reference
         "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC)
          Label Switching Routers,

          ITU-T G.694.2 (12/2003): Spectral grids for WDM applications:
          CWDM wavelength grid";
     }

       identity cwdm-20nm {
         base cwdm-ch-spc-type;
         description
           "20nm channel spacing";
         reference
           "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC)
           Label Switching Routers,

           ITU-T G.694.2 (12/2003): Spectral grids for WDM applications:
           CWDM wavelength grid";
       }

     identity dwdm-ch-spc-type {
       description
         "DWDM channel-spacing type";
       reference
         "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC)
          Label Switching Routers,

          ITU-T G.694.1 (10/2020): Spectral grids for WDM applications:
          DWDM frequency grid";
     }

       identity dwdm-100ghz {
         base dwdm-ch-spc-type;



Belotti, et al.            Expires 7 June 2025                 [Page 13]

Internet-Draft            L0 Common YANG Types             December 2024


         description
           "100 GHz channel spacing";
         reference
           "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC)
           Label Switching Routers,

           ITU-T G.694.1 (10/2020): Spectral grids for WDM applications:
           DWDM frequency grid";
       }

       identity dwdm-50ghz {
         base dwdm-ch-spc-type;
         description
           "50 GHz channel spacing";
         reference
           "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC)
           Label Switching Routers,

           ITU-T G.694.1 (10/2020): Spectral grids for WDM applications:
           DWDM frequency grid";
       }

       identity dwdm-25ghz {
         base dwdm-ch-spc-type;
         description
           "25 GHz channel spacing";
         reference
           "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC)
           Label Switching Routers,

           ITU-T G.694.1 (10/2020): Spectral grids for WDM applications:
           DWDM frequency grid";
       }

       identity dwdm-12p5ghz {
         base dwdm-ch-spc-type;
         description
           "12.5 GHz channel spacing";
         reference
           "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC)
           Label Switching Routers,

           ITU-T G.694.1 (10/2020): Spectral grids for WDM applications:
           DWDM frequency grid";
       }

     identity flexi-ch-spc-type {
       status deprecated;



Belotti, et al.            Expires 7 June 2025                 [Page 14]

Internet-Draft            L0 Common YANG Types             December 2024


       description
         "Flexi-grid channel-spacing type";
     }

       identity flexi-ch-spc-6p25ghz {
         base flexi-ch-spc-type;
         status deprecated;
         description
           "6.25 GHz channel spacing";
       }

     identity flexi-ncfg-type {
       description
         "Flexi-grid Nominal Central Frequency Granularity (NCFG)
         type";
       reference
         "RFC 7699: Generalized Labels for the Flexi-Grid in Lambda
         Switch Capable (LSC) Label Switching Routers,

         ITU-T G.694.1 (10/2020): Spectral grids for WDM applications:
         DWDM frequency grid";
     }

       identity flexi-ncfg-6p25ghz {
         base flexi-ncfg-type;
         description
           "6.25 GHz Nominal Central Frequency Granularity (NCFG)";
         reference
           "RFC 7699: Generalized Labels for the Flexi-Grid in Lambda
           Switch Capable (LSC) Label Switching Routers,

           ITU-T G.694.1 (10/2020): Spectral grids for WDM applications:
           DWDM frequency grid";
       }

     identity flexi-slot-width-granularity {
       description
         "Flexi-grid slot width granularity";
       reference
         "RFC 7699: Generalized Labels for the Flexi-Grid in Lambda
         Switch Capable (LSC) Label Switching Routers,

         ITU-T G.694.1 (10/2020): Spectral grids for WDM applications:
         DWDM frequency grid";
     }

       identity flexi-swg-12p5ghz {
         base flexi-slot-width-granularity;



Belotti, et al.            Expires 7 June 2025                 [Page 15]

Internet-Draft            L0 Common YANG Types             December 2024


         description
           "12.5 GHz slot width granularity";
         reference
           "RFC 7699: Generalized Labels for the Flexi-Grid in Lambda
           Switch Capable (LSC) Label Switching Routers,

           ITU-T G.694.1 (10/2020): Spectral grids for WDM applications:
           DWDM frequency grid";
       }

     identity modulation {
       description "base identity for modulation type";
     }

       identity DPSK {
         base modulation;
         description
           "DPSK (Differential Phase Shift Keying) modulation";
       }

       identity QPSK {
         base modulation;
         description
           "QPSK (Quadrature Phase Shift Keying) modulation";
       }

       identity DP-QPSK {
         base modulation;
         description
           "DP-QPSK (Dual Polarization Quadrature
           Phase Shift Keying) modulation";
       }

       identity QAM8 {
         base modulation;
         description
           "8QAM (8 symbols Quadrature Amplitude Modulation)";
       }

       identity DP-QAM8 {
         base modulation;
         description
           "DP-QAM8 (8 symbols Dual Polarization Quadrature Amplitude
           Modulation)";
       }

       identity QAM16 {
         base modulation;



Belotti, et al.            Expires 7 June 2025                 [Page 16]

Internet-Draft            L0 Common YANG Types             December 2024


         description
           "QAM16 (16 symbols Quadrature Amplitude Modulation)";
       }

       identity DP-QAM16 {
         base modulation;
         description
           "DP-QAM16 (16 symbols Dual Polarization Quadrature Amplitude
           Modulation)";
       }

       identity QAM32 {
         base modulation;
         description
           "QAM32 (32 symbols Quadrature Amplitude Modulation)";
       }

       identity DP-QAM32 {
         base modulation;
         description
           "DP-QAM32 (32 symbols Dual Polarization Quadrature Amplitude
           Modulation)";
       }

       identity QAM64 {
         base modulation;
         description
           "QAM64 (64 symbols Quadrature Amplitude Modulation)";
       }

       identity DP-QAM64 {
         base modulation;
         description
           "DP-QAM64 (64 symbols Dual Polarization Quadrature Amplitude
           Modulation)";
       }

     identity fec-type {
       description
         "Base identity from which specific FEC
         (Forward Error Correction) type identities are derived.";
     }

       identity g-fec {
         base fec-type;
         description
           "Generic Forward Error Correction (G-FEC).";
         reference



Belotti, et al.            Expires 7 June 2025                 [Page 17]

Internet-Draft            L0 Common YANG Types             December 2024


           "ITU-T G.975 v2.0 (10/2000): Forward error correction for
           submarine systems.";
       }

       identity super-fec {
         base fec-type;
         description
           "Super Forward Error Correction (S-FEC).";
         reference
           "ITU-T G.975.1 v1.2 (07/2013): Forward error correction for
           high bit-rate DWDM submarine systems.";
       }

       identity no-fec {
         base fec-type;
         description
           "No FEC";
       }

       identity sc-fec {
         base fec-type;
         description
           "Staircase Forward Error Correction (SC-FEC).";
         reference
           "Annex A of ITU-T G.709.2 v1.1 (09/2020):OTU4 long-reach
           interface.";
       }

       identity o-fec {
         base fec-type;
         description
           "Open Forward Error Correction (O-FEC) which reuses the
           Bose, Chaudhuri and Hocquenghem (BCH) FEC.";
         reference
           "Clause 16.4.4 of ITU-T G.709.3 v2.1 (11/2022): Flexible OTN
           long-reach interfaces;

           Annex E of ITU-T G.709.3 v2.1 (11/2022): Flexible OTN
           long-reach interfaces.";
       }

       identity c-fec {
         base fec-type;
         description
           "Concatenated FEC (C-FEC) that combines an outer Staircase
           Forward Error Correction (SC-FEC) code and an inner
           double-extended SD-FEC (128,119) Hamming code.




Belotti, et al.            Expires 7 June 2025                 [Page 18]

Internet-Draft            L0 Common YANG Types             December 2024


           More details are provided in clause 15/G.709.3 where it is
           called DSH instead of concatenated FEC.";
         reference
           "Annex A of ITU-T G.709.2 v1.1 (09/2020):OTU4 long-reach
           interface;

           Annex D of ITU-T G.709.3 v2.1 (11/2022): Flexible OTN
           long-reach interfaces;

           Clause 15 of ITU-T G.709.3 v2.1 (11/2022): Flexible OTN
           long-reach interfaces.";
       }

     identity line-coding {
       description
         "Base identity to defined the bit rate/line coding of optical
         tributary signals.";
       reference
         "Section 7.1.2 of ITU-T G.698.2 v3.0 (11/2018).";
     }

       identity line-coding-NRZ-2p5G {
         base line-coding;
         description
           "The non return to zero (NRZ) bit rate/line coding used by
           the optical tributary signal class NRZ 2.5G";
         reference
           "Section 3.2.6 of ITU-T G.959.1 v8.0 (07/2018).";
       }

       identity line-coding-NRZ-OTU1 {
         base line-coding;
         description
           "The non return to zero (NRZ) bit rate/line coding used by
           the Optical channel Transport Unit order 1 (OTU1) optical
           tributary signals";
         reference
           "Section 7.2.1.2 of ITU-T G.959.1 v8.0 (07/2018).";
       }

       identity line-coding-NRZ-10G {
         description
           "The non return to zero (NRZ) bit rate/line coding used by
           the optical tributary signal class NRZ 10G";
         reference
           "Section 3.2.7 of ITU-T G.959.1 v8.0 (07/2018).";
       }




Belotti, et al.            Expires 7 June 2025                 [Page 19]

Internet-Draft            L0 Common YANG Types             December 2024


       identity line-coding-NRZ-OTU2 {
         base line-coding;
         description
           "The non return to zero (NRZ) bit rate/line coding used by
           the Optical channel Transport Unit order 2 (OTU2) optical
           tributary signals";
         reference
           "Section 7.2.1.2 of ITU-T G.959.1 v8.0 (07/2018).";
       }

       identity line-coding-OTL4.4-SC {
         base line-coding;
         description
           "The bit rate/line coding used by optical tributary
           signals carrying a 100G Optical Transport Unit order 4
           (OTU4) with Staircase Forward Error Correction (SC FEC)
           from a group of four Optical Transport Lanes (OTL).";
         reference
           "Section 3.2.1 of ITU-T G.698.2 v3.0 (11/2018).";
       }

       identity line-coding-FOIC1.4-SC {
         base line-coding;
         description
           "The bit rate/line coding used by optical tributary signals
           carrying a FlexO Interface of order C1 with 4 lanes
           (FOIC1.1) with Staircase Forward Error Correction
           (SC FEC).";
         reference
           "Section 3.2.1 of ITU-T G.698.2 v3.0 (11/2018).";
       }

     identity wavelength-assignment {
       description
         "Wavelength selection base";
       reference
         "RFC 7689: Signaling Extensions for Wavelength Switched
         Optical Networks";
     }

       identity first-fit-wavelength-assignment {
         base wavelength-assignment;
         description
           "All the available wavelengths are numbered,
           and this WA (Wavelength Assignment) method chooses
           the available wavelength with the lowest index";
         reference
           "RFC 7689: Signaling Extensions for Wavelength Switched



Belotti, et al.            Expires 7 June 2025                 [Page 20]

Internet-Draft            L0 Common YANG Types             December 2024


           Optical Networks";
       }

       identity random-wavelength-assignment {
         base wavelength-assignment;
         description
           "This WA method chooses an available
           wavelength randomly";
         reference
           "RFC 7689: Signaling Extensions for Wavelength Switched
           Optical Networks";
       }

       identity least-loaded-wavelength-assignment {
         base wavelength-assignment;
         description
           "This WA method selects the wavelength that
           has the largest residual capacity on the most loaded
           link along the route (in multi-fiber networks)";
         reference
           "RFC 7689: Signaling Extensions for Wavelength Switched
           Optical Networks";
       }

       identity lower-first-wavelength-assignment {
         base wavelength-assignment;
         description
           "Allocate wavelengths in ascending order, beginning from the
           lowest frequency and progressing toward the highest frequency
           within the permissible frequency range.";
       }

       identity upper-first-wavelength-assignment {
         base wavelength-assignment;
         description
           "Allocate wavelengths in decending order, beginning from the
           highest frequency and progressing toward the lowest frequency
           within the permissible frequency range.";
       }

     identity type-power-mode {
       description
         "power equalization mode used within the
          OMS and its elements";
     }

       identity power-spectral-density {
         base type-power-mode;



Belotti, et al.            Expires 7 June 2025                 [Page 21]

Internet-Draft            L0 Common YANG Types             December 2024


         description
           "all elements must use power spectral density (W/Hz)";
       }

       identity carrier-power {
         base type-power-mode;
         description
           "all elements must use power (dBm)";
       }

     identity switching-wson-lsc {
       base te-types:switching-lsc;
       description
         "Wavelength Switched Optical Network Lambda-Switch Capable
         (WSON-LSC).";
       reference
         "Section 3 of RFC 7688: GMPLS OSPF Enhancement for Signal and
         Network Element Compatibility for Wavelength Switched Optical
         Networks";
     }

     identity switching-flexi-grid-lsc {
       base te-types:switching-lsc;
       description
         "Flexi-grid Lambda-Switch Capable (Flexi-Grid-LSC).";
       reference
         "Section 4.1 of RFC 8363: GMPLS OSPF-TE Extensions in Support
         of Flexi-Grid Dense Wavelength Division Multiplexing (DWDM)
         Networks";
     }

   /*
    * Typedefs
    */

     typedef dwdm-n {
       type int16;
       description
         "The given value 'N' is used to determine the nominal central
          frequency.

          The nominal central frequency, 'f', is defined by:
            f = 193100.000 GHz + N x channel spacing (measured in GHz),

          where 193100.000 GHz (193.100000 THz) is the ITU-T 'anchor
          frequency' for transmission over the DWDM grid, and where
          'channel spacing' is defined by the dwdm-ch-spc-type.";
       reference



Belotti, et al.            Expires 7 June 2025                 [Page 22]

Internet-Draft            L0 Common YANG Types             December 2024


         "RFC6205: Generalized Labels for Lambda-Switch-Capable (LSC)
          Label Switching Routers,

          ITU-T G.694.1 (10/2020): Spectral grids for WDM applications:
          DWDM frequency grid";
     }

     typedef cwdm-n {
       type int16;
       description
         "The given value 'N' is used to determine the nominal central
          wavelength.

          The nominal central wavelength is defined by:
            Wavelength = 1471 nm + N x channel spacing (measured in nm)

          where 1471 nm is the conventional 'anchor wavelength' for
          transmission over the CWDM grid, and where 'channel spacing'
          is defined by the cwdm-ch-spc-type.";
       reference
         "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC)
          Label Switching Routers,

          ITU-T G.694.2 (12/2003): Spectral grids for WDM applications:
          CWDM wavelength grid";
     }

     typedef flexi-n {
       type int16;
       description
         "The given value 'N' is used to determine the nominal central
          frequency.

          The nominal central frequency, 'f', is defined by:
            f = 193100.000 GHz + N x NCFG (measured in GHz),

          where 193100.000 GHz (193.100000 THz) is the ITU-T 'anchor
          frequency' for transmission over the DWDM grid, and where
          NCFG is defined by the flexi-ncfg-type, or by the deprecated
          flexi-ch-spc-type.";
       reference
         "RFC 7699: Generalized Labels for the Flexi-Grid in Lambda
         Switch Capable (LSC) Label Switching Routers,

          ITU-T G.694.1 (10/2020): Spectral grids for WDM applications:
          DWDM frequency grid";
     }




Belotti, et al.            Expires 7 June 2025                 [Page 23]

Internet-Draft            L0 Common YANG Types             December 2024


     typedef flexi-m {
       type uint16;
       description
         "The given value 'M' is used to determine the slot width.

          A slot width is defined by:
            slot width = M x SWG (measured in GHz),

          where SWG is defined by the flexi-slot-width-granularity.";
       reference
         "RFC 7699: Generalized Labels for the Flexi-Grid in Lambda
         Switch Capable (LSC) Label Switching Routers,

          ITU-T G.694.1 (10/2020): Spectral grids for WDM applications:
          DWDM frequency grid";
     }

     typedef standard-mode {
       type string;
       description
         "Identifies an ITU-T G.698.2 standard application code.

         It MUST be a string with a format that follows the
         nomenclature defined in section 5.3 of ITU-T G.698.2.";
       reference
         "ITU-T G.698.2 (11/2018)";
     }

     typedef organization-identifier {
       type string;
       description
         "vendor/organization identifier that uses a private mode
         out of already defined in G.698.2 ITU-T application-code";
       reference
         "Section 2.5.2 of RFC YYYY: A YANG Data Model for Optical
         Impairment-aware Topology.";
     }
   // RFC Ed.: replace YYYY with actual RFC number and remove
   // this note after draft-ietf-ccamp-optical-impairment-topology-yang
   // is published as an RFC

     typedef operational-mode {
       type string;
       description
         "Identifies an organization (e.g., vendor) specific mode.

         The format of the string has to be defined by the
         organization which is responsible for defining the



Belotti, et al.            Expires 7 June 2025                 [Page 24]

Internet-Draft            L0 Common YANG Types             December 2024


         corresponding optical interface specification.";
       reference
         "Section 2.5.2 of RFC YYYY: A YANG Data Model for Optical
         Impairment-aware Topology.";
     }
   // RFC Ed.: replace YYYY with actual RFC number and remove
   // this note after draft-ietf-ccamp-optical-impairment-topology-yang
   // is published as an RFC

     typedef frequency-thz {
       type decimal64 {
         fraction-digits 9;
       }
       units "THz";
       description
         "The DWDM frequency in THz, e.g., 193.112500000";
     }

     typedef frequency-ghz {
       type decimal64 {
         fraction-digits 6;
       }
       units "GHz";
       description
         "The DWDM frequency in GHz, e.g., 193112.500000";
     }

     typedef snr {
       type decimal-2;
       units "dB@0.1nm";
       description
         "(Optical) Signal to Noise Ratio measured over 0.1 nm
         resolution bandwidth";
       reference
         "ITU-T G.977.1 (02/2021): Transverse compatible dense
         wavelength division multiplexing applications for repeatered
         optical fibre submarine cable systems";
     }

     typedef snr-or-null {
       type union {
         type snr;
         type empty;
       }
       description
         "(Optical) Signal to Noise Ratio measured over 0.1 nm
         resolution bandwidth, when known, or an empty value when
         unknown.";



Belotti, et al.            Expires 7 June 2025                 [Page 25]

Internet-Draft            L0 Common YANG Types             December 2024


     }

     typedef fiber-type {
       type enumeration {
         enum G.652 {
           description
             "G.652 Standard Singlemode Fiber";
         }
         enum G.654 {
           description
             "G.654 Cutoff Shifted Fiber";
         }
         enum G.653 {
           description "G.653 Dispersion Shifted Fiber";
         }
         enum G.655 {
           description "G.655 Non-Zero Dispersion Shifted Fiber";
         }
         enum G.656 {
           description
             "G.656 Non-Zero Dispersion for Wideband Optical Transport";
         }
         enum G.657 {
           description
             "G.657 Bend-Insensitive Fiber";
         }
       }
       description
         "ITU-T based fiber-types";
     }

     typedef decimal-2 {
       type decimal64 {
         fraction-digits 2;
       }
       description
         "A decimal64 value with two digits.";
     }

     typedef decimal-2-or-null {
       type union {
         type decimal-2;
         type empty;
       }
       description
         "A decimal64 value with two digits, when the value is known or
         an empty value when the value is not known.";
     }



Belotti, et al.            Expires 7 June 2025                 [Page 26]

Internet-Draft            L0 Common YANG Types             December 2024


     typedef power-gain {
       type decimal-2 {
         range "0..max";
       }
       units "dB";
       description
         "The gain in dB.";
     }

     typedef power-gain-or-null {
       type union {
         type power-gain;
         type empty;
       }
       description
         "The gain in dB, when it is known or an empty
         value when the power gain/loss is not known.";
     }

     typedef power-loss {
       type decimal-2 {
         range "0..max";
       }
       units "dB";
       description
         "The power attenuation in dB.";
     }

     typedef power-loss-or-null {
       type union {
         type power-loss;
         type empty;
       }
       description
         "The power attenuation in dB, when it is known or an empty
         value when the loss is not known.";
     }

     typedef power-ratio {
       type decimal-2;
       units "dB";
       description
         "The power difference in dB.";
     }

     typedef power-ratio-or-null {
       type union {
         type power-ratio;



Belotti, et al.            Expires 7 June 2025                 [Page 27]

Internet-Draft            L0 Common YANG Types             December 2024


         type empty;
       }
       description
         "The power difference in dB, when it is known or an empty
         value when the difference is not known.";
     }

     typedef power-dbm {
       type decimal-2;
       units "dBm";
       description
         "The power in dBm.";
     }

     typedef power-dbm-or-null {
       type union {
         type power-dbm;
         type empty;
       }
       description
         "The power in dBm, when it is known or an empty value when the
         power is not known.";
     }

     typedef decimal-5 {
       type decimal64 {
         fraction-digits 5;
       }
       description
         "A decimal64 value with five digits.";
     }

     typedef decimal-5-or-null {
       type union {
         type decimal-5;
         type empty;
       }
       description
         "A decimal64 value with five digits, when the value is known
         or an empty value when the value is not known.";
     }

     typedef psd {
       type decimal64 {
         fraction-digits 16;
       }
       units "W/Hz";
       description



Belotti, et al.            Expires 7 June 2025                 [Page 28]

Internet-Draft            L0 Common YANG Types             December 2024


         "The power spectral density (PSD).

         Typical value : 3.9 E-14, resolution 0.1nW/MHz.";
       reference
         "ITU-T G.9700 (07/2019): Fast access to subscriber terminals
         (G.fast) - Power spectral density specification";
     }

     typedef psd-or-null {
       type union {
         type psd;
         type empty;
       }
       description
         "The power spectral density (PSD), when it is known or an
         empty value when the PSD is not known.";
     }

     typedef decimal-18 {
       type decimal64 {
         fraction-digits 18;
       }
       description
         "A decimal64 value with eighteen digits.";
     }

     typedef decimal-18-or-null {
       type union {
         type decimal-18;
         type empty;
       }
       description
         "A decimal64 value with eighteen digits, when the value is
         known or an empty value when the value is not known.";
     }

   /*
    * Groupings
    */

     grouping wdm-label-start-end {
       description
         "The WDM label-start or label-end used to specify DWDM and
          CWDM label range.";

       choice grid-type {
         description
           "Label for fixed & flexi-DWDM or CWDM grid";



Belotti, et al.            Expires 7 June 2025                 [Page 29]

Internet-Draft            L0 Common YANG Types             December 2024


         case fixed-dwdm {
           leaf dwdm-n {
             when "derived-from-or-self(../../../grid-type,
                   \"wson-grid-dwdm\")" {
               description
                 "Valid only when grid type is DWDM.";
             }
             type l0-types:dwdm-n;
             description
               "The given value 'N' is used to determine the
                nominal central frequency.";
             reference
               "RFC 6205: Generalized Labels for Lambda-Switch-Capable
                (LSC) Label Switching Routers";
           }
         }
         case cwdm {
           leaf cwdm-n {
             when "derived-from-or-self(../../../grid-type,
                   \"wson-grid-cwdm\")" {
               description
                 "Valid only when grid type is CWDM.";
             }
             type l0-types:cwdm-n;
             description
               "The given value 'N' is used to determine the nominal
                central wavelength.";
             reference
               "RFC 6205: Generalized Labels for Lambda-Switch-Capable
                (LSC) Label Switching Routers";
           }
         }
         case flexi-grid {
           uses l0-types:flexi-grid-label-start-end;
         }
       }
       reference
         "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC)
          Label Switching Routers";
     }

     grouping wdm-label-step {
       description
         "Label step information for fixed & flexi-DWDM or CWDM grid";
       choice l0-grid-type {
         description
           "Grid type: DWDM, CWDM, etc.";
         case fixed-dwdm {



Belotti, et al.            Expires 7 June 2025                 [Page 30]

Internet-Draft            L0 Common YANG Types             December 2024


           leaf wson-dwdm-channel-spacing {
             when "derived-from-or-self(../../grid-type,
                   \"wson-grid-dwdm\")" {
               description
                 "Valid only when grid type is DWDM.";
             }
             type identityref {
               base dwdm-ch-spc-type;
             }
             description
               "Label-step is the channel spacing (GHz), e.g., 100.000,
                50.000, 25.000, or 12.500 GHz for DWDM.";
             reference
               "RFC 6205: Generalized Labels for Lambda-Switch-Capable
                (LSC) Label Switching Routers";
           }
         }
         case cwdm {
           leaf wson-cwdm-channel-spacing {
             when "derived-from-or-self(../../grid-type,
                   \"wson-grid-cwdm\")" {
               description
                 "Valid only when grid type is CWDM.";
             }
             type identityref {
               base cwdm-ch-spc-type;
             }
             description
               "Label-step is the channel spacing (nm), i.e., 20 nm
                for CWDM, which is the only value defined for CWDM.";
             reference
               "RFC 6205: Generalized Labels for Lambda-Switch-Capable
                (LSC) Label Switching Routers";
           }
         }
         case flexi-grid {
           uses flexi-grid-label-step;
         }
       }
       reference
         "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC)
          Label Switching Routers,
          ITU-T G.694.2 (12/2003): Spectral grids for WDM applications:
          CWDM wavelength grid,
          RFC 8363: GMPLS OSPF-TE Extensions in Support of Flexi-Grid
          Dense Wavelength Division Multiplexing (DWDM) Networks";
     }




Belotti, et al.            Expires 7 June 2025                 [Page 31]

Internet-Draft            L0 Common YANG Types             December 2024


     grouping wdm-label-hop {
       description
         "Generic label-hop information for fixed & flexi-DWDM or
          CWDM grid";
       choice grid-type {
         description
           "Label for DWDM or CWDM grid";
         case fixed-dwdm {
           choice fixed-single-or-super-channel {
             description
               "single or super channel";
             case single {
               leaf dwdm-n {
                 type l0-types:dwdm-n;
                 description
                   "The given value 'N' is used to determine the
                    nominal central frequency.";
               }
             }
             case multi {
               leaf-list subcarrier-dwdm-n {
                 type l0-types:dwdm-n;
                 min-elements 2;
                 description
                   "The given values 'N' are used to determine the
                    nominal central frequency for each subcarrier
                    channel.";
                 reference
                   "ITU-T G.694.1 (10/2020): Spectral grids for WDM
                   applications: DWDM frequency grid";
               }
             }
           }
         }
         case cwdm {
           leaf cwdm-n {
             type l0-types:cwdm-n;
             description
               "The given value 'N' is used to determine the nominal
                central wavelength.";
             reference
               "RFC 6205: Generalized Labels for Lambda-Switch-Capable
                (LSC) Label Switching Routers";
           }
         }
         case flexi-grid {
           uses l0-types:flexi-grid-label-hop;
         }



Belotti, et al.            Expires 7 June 2025                 [Page 32]

Internet-Draft            L0 Common YANG Types             December 2024


       }
       reference
         "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC)
          Label Switching Routers";
     }

     grouping wdm-label-range-info {
       description
         "WDM label range related information";
       uses l0-label-range-info;
       container flexi-grid {
         when "derived-from-or-self(../grid-type,
             \"flexi-grid-dwdm\")" {
           description
             "Applicable only when the grid type is flexi-grid-dwdm.";
         }
         description
           "flexi-grid definition";
         leaf slot-width-granularity {
           type identityref {
             base flexi-slot-width-granularity;
           }
           default "flexi-swg-12p5ghz";
           description
             "Minimum space between slot widths. Default is 12.500
              GHz.";
           reference
             "RFC 7698: Framework and Requirements for GMPLS-Based
              Control of Flexi-Grid Dense Wavelength Division
              Multiplexing (DWDM) Networks";
         }
         leaf min-slot-width-factor {
           type uint16 {
             range "1..max";
           }
           default "1";
           description
             "A multiplier of the slot width granularity, indicating
              the minimum slot width supported by an optical port.

              Minimum slot width is calculated by:
                Minimum slot width (GHz) =
                  min-slot-width-factor * slot-width-granularity.";
           reference
             "RFC 8363: GMPLS OSPF-TE Extensions in Support of Flexi-
              Grid Dense Wavelength Division Multiplexing (DWDM)
              Networks";
         }



Belotti, et al.            Expires 7 June 2025                 [Page 33]

Internet-Draft            L0 Common YANG Types             December 2024


         leaf max-slot-width-factor {
           type uint16 {
             range "1..max";
           }
           must '. >= ../min-slot-width-factor' {
             error-message
               "Maximum slot width must be greater than or equal to
                minimum slot width.";
           }
           description
             "A multiplier of the slot width granularity, indicating
              the maximum slot width supported by an optical port.

              Maximum slot width is calculated by:
                Maximum slot width (GHz) =
                  max-slot-width-factor * slot-width-granularity

              If specified, maximum slot width must be greater than or
              equal to minimum slot width.  If not specified, maximum
              slot width is equal to minimum slot width.";
           reference
             "RFC 8363: GMPLS OSPF-TE Extensions in Support of Flexi-
              Grid Dense Wavelength Division Multiplexing (DWDM)
              Networks";
         }
       }
     }

     grouping wson-label-start-end {
       description
         "The WSON label-start or label-end used to specify WSON label
          range.";
       choice grid-type {
         description
           "Label for DWDM or CWDM grid";
         case dwdm {
           leaf dwdm-n {
             when "derived-from-or-self(../../../grid-type,
                   \"wson-grid-dwdm\")" {
               description
                 "Valid only when grid type is DWDM.";
             }
             type l0-types:dwdm-n;
             description
               "The central frequency of DWDM.";
             reference
               "RFC 6205: Generalized Labels for Lambda-Switch-Capable
                (LSC) Label Switching Routers";



Belotti, et al.            Expires 7 June 2025                 [Page 34]

Internet-Draft            L0 Common YANG Types             December 2024


           }
         }
         case cwdm {
           leaf cwdm-n {
             when "derived-from-or-self(../../../grid-type,
                   \"wson-grid-cwdm\")" {
               description
                 "Valid only when grid type is CWDM.";
             }
             type l0-types:cwdm-n;
             description
               "Channel wavelength computing input.";
             reference
               "RFC 6205: Generalized Labels for Lambda-Switch-Capable
                (LSC) Label Switching Routers";
           }
         }
       }
       reference
         "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC)
          Label Switching Routers";
     }

     grouping wson-label-hop {
       description
         "Generic label-hop information for WSON";
       choice grid-type {
         description
           "Label for DWDM or CWDM grid";
         case dwdm {
           choice single-or-super-channel {
             description
               "single or super channel";
             case single {
               leaf dwdm-n {
                 type l0-types:dwdm-n;
                 description
                   "The given value 'N' is used to determine the
                    nominal central frequency.";
               }
             }
             case super {
               leaf-list subcarrier-dwdm-n {
                 type l0-types:dwdm-n;
                 description
                   "The given values 'N' are used to determine the
                    nominal central frequency for each subcarrier
                    channel.";



Belotti, et al.            Expires 7 June 2025                 [Page 35]

Internet-Draft            L0 Common YANG Types             December 2024


                 reference
                   "ITU-T G.694.1 (10/2020): Spectral grids for WDM
                   applications: DWDM frequency grid";
               }
             }
           }
         }
         case cwdm {
           leaf cwdm-n {
             type l0-types:cwdm-n;
             description
               "The given value 'N' is used to determine the nominal
                central wavelength.";
             reference
               "RFC 6205: Generalized Labels for Lambda-Switch-Capable
                (LSC) Label Switching Routers";
           }
         }
       }
       reference
         "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC)
          Label Switching Routers";
     }

     grouping l0-label-range-info {
       description
         "Information about Layer 0 label range.";
       leaf grid-type {
         type identityref {
           base l0-grid-type;
         }
         description
           "Grid type";
       }
       leaf priority {
         type uint8;
         description
           "Priority in Interface Switching Capability Descriptor
            (ISCD).";
         reference
           "RFC 4203: OSPF Extensions in Support of Generalized
            Multi-Protocol Label Switching (GMPLS)";
       }
       reference
         "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC)
          Label Switching Routers";
     }




Belotti, et al.            Expires 7 June 2025                 [Page 36]

Internet-Draft            L0 Common YANG Types             December 2024


     grouping wson-label-step {
       description
         "Label step information for WSON";
       choice l0-grid-type {
         description
           "Grid type: DWDM, CWDM, etc.";
         case dwdm {
           leaf wson-dwdm-channel-spacing {
             when "derived-from-or-self(../../grid-type,
                   \"wson-grid-dwdm\")" {
               description
                 "Valid only when grid type is DWDM.";
             }
             type identityref {
               base dwdm-ch-spc-type;
             }
             description
               "Label-step is the channel spacing (GHz), e.g., 100.000,
                50.000, 25.000, or 12.500 GHz for DWDM.";
             reference
               "RFC 6205: Generalized Labels for Lambda-Switch-Capable
                (LSC) Label Switching Routers";
           }
         }
         case cwdm {
           leaf wson-cwdm-channel-spacing {
             when "derived-from-or-self(../../grid-type,
                   \"wson-grid-cwdm\")" {
               description
                 "Valid only when grid type is CWDM.";
             }
             type identityref {
               base cwdm-ch-spc-type;
             }
             description
               "Label-step is the channel spacing (nm), i.e., 20 nm
                for CWDM, which is the only value defined for CWDM.";
             reference
               "RFC 6205: Generalized Labels for Lambda-Switch-Capable
                (LSC) Label Switching Routers";
           }
         }
       }
       reference
         "RFC 6205: Generalized Labels for Lambda-Switch-Capable (LSC)
          Label Switching Routers,

          ITU-T G.694.2 (12/2003): Spectral grids for WDM applications:



Belotti, et al.            Expires 7 June 2025                 [Page 37]

Internet-Draft            L0 Common YANG Types             December 2024


          CWDM wavelength grid";
     }

     grouping flexi-grid-label-start-end {
       description
         "The flexi-grid label-start or label-end used to specify
          flexi-grid label range.";
       leaf flexi-n {
         type l0-types:flexi-n;
         description
           "The given value 'N' is used to determine the nominal
           central frequency.

           As described in section 3.1 of RFC 8363, the range of
           available nominal central frequencies are advertised for
           m=1, which means that for an available central frequency n,
           the frequency slot from central frequency n-1 to central
           frequency n+1 is available.";
       }
       reference
         "RFC 7699: Generalized Labels for the Flexi-Grid in Lambda
         Switch Capable (LSC) Label Switching Routers,

         RFC 8363: GMPLS OSPF-TE Extensions in Support of Flexi-Grid
         Dense Wavelength Division Multiplexing (DWDM) Networks";
     }

     grouping flexi-grid-frequency-slot {
       description
         "Flexi-grid frequency slot grouping.";
       uses flexi-grid-label-start-end;
       leaf flexi-m {
         type l0-types:flexi-m;
         description
           "The given value 'M' is used to determine the slot width.";
       }
       reference
         "RFC 7699: Generalized Labels for the Flexi-Grid in Lambda
         Switch Capable (LSC) Label Switching Routers";
     }

     grouping flexi-grid-label-hop {
       description
         "Generic label-hop information for flexi-grid";
       choice single-or-super-channel {
         description
           "single or super channel";
         case single {



Belotti, et al.            Expires 7 June 2025                 [Page 38]

Internet-Draft            L0 Common YANG Types             December 2024


           uses flexi-grid-frequency-slot;
         }
         case super {
           status deprecated;
           list subcarrier-flexi-n {
             key "flexi-n";
             status deprecated;
             uses flexi-grid-frequency-slot {
               status deprecated;
             }
             description
               "List of subcarrier channels for flexi-grid super
                channel.";
           }
         }
         case multi {
           container frequency-slots {
             description
               "The top level container for the list of frequency
               slots used for flexi-grid super channel.";
             list frequency-slot {
               key "flexi-n";
               min-elements 2;
               uses flexi-grid-frequency-slot;
               description
                 "List of frequency slots used for flexi-grid super
                 channel.";
             }
           }
         }
       }
       reference
         "RFC 8363: GMPLS OSPF-TE Extensions in Support of Flexi-Grid
         Dense Wavelength Division Multiplexing (DWDM) Networks";
     }

     grouping flexi-grid-label-range-info {
       description
         "Flexi-grid-specific label range related information";
       uses l0-label-range-info;
       container flexi-grid {
         description
           "flexi-grid definition";
         leaf slot-width-granularity {
           type identityref {
             base flexi-slot-width-granularity;
           }
           default "flexi-swg-12p5ghz";



Belotti, et al.            Expires 7 June 2025                 [Page 39]

Internet-Draft            L0 Common YANG Types             December 2024


           description
             "Minimum space between slot widths. Default is 12.500
              GHz.";
           reference
             "RFC 8363: GMPLS OSPF-TE Extensions in Support of
             Flexi-Grid Dense Wavelength Division Multiplexing (DWDM)
             Networks";
         }
         leaf min-slot-width-factor {
           type uint16 {
             range "1..max";
           }
           default "1";
           description
             "A multiplier of the slot width granularity, indicating
              the minimum slot width supported by an optical port.

              Minimum slot width is calculated by:
                Minimum slot width (GHz) =
                  min-slot-width-factor * slot-width-granularity.";
           reference
             "RFC 8363: GMPLS OSPF-TE Extensions in Support of Flexi-
              Grid Dense Wavelength Division Multiplexing (DWDM)
              Networks";
         }
         leaf max-slot-width-factor {
           type uint16 {
             range "1..max";
           }
           must '. >= ../min-slot-width-factor' {
             error-message
               "Maximum slot width must be greater than or equal to
                minimum slot width.";
           }
           description
             "A multiplier of the slot width granularity, indicating
              the maximum slot width supported by an optical port.

              Maximum slot width is calculated by:
                Maximum slot width (GHz) =
                  max-slot-width-factor * slot-width-granularity

              If specified, maximum slot width must be greater than or
              equal to minimum slot width.  If not specified, maximum
              slot width is equal to minimum slot width.";
           reference
             "RFC 8363: GMPLS OSPF-TE Extensions in Support of Flexi-
              Grid Dense Wavelength Division Multiplexing (DWDM)



Belotti, et al.            Expires 7 June 2025                 [Page 40]

Internet-Draft            L0 Common YANG Types             December 2024


              Networks";
         }
       }
     }

     grouping flexi-grid-label-step {
       description
         "Label step information for flexi-grid";
       leaf flexi-grid-channel-spacing {
         type identityref {
           base flexi-ch-spc-type;
         }
         default "flexi-ch-spc-6p25ghz";
         status deprecated;
         description
           "Label-step is the nominal central frequency granularity
            (GHz), e.g., 6.25 GHz.";
         reference
           "RFC 7699: Generalized Labels for the Flexi-Grid in Lambda
            Switch Capable (LSC) Label Switching Routers";
       }
       leaf flexi-ncfg {
         type identityref {
           base flexi-ncfg-type;
         }
         default "flexi-ncfg-6p25ghz";
         description
           "Label-step is the nominal central frequency granularity
            (GHz), e.g., 6.25 GHz.";
         reference
           "RFC 7699: Generalized Labels for the Flexi-Grid in Lambda
            Switch Capable (LSC) Label Switching Routers";
       }
       leaf flexi-n-step {
         type uint8;
         description
           "This attribute defines the multiplier for the supported
            values of 'N'.

            For example, given a grid with a nominal central frequency
            granularity of 6.25 GHz, the granularity of the supported
            values of the nominal central frequency could be 12.5 GHz.
            In this case, the values of flexi-n should be even and this
            constraint is reported by setting the flexi-n-step to 2.

            This attribute is also known as central frequency
            granularity in RFC 8363.";
         reference



Belotti, et al.            Expires 7 June 2025                 [Page 41]

Internet-Draft            L0 Common YANG Types             December 2024


           "RFC 8363: GMPLS OSPF-TE Extensions in Support of Flexi-Grid
            Dense Wavelength Division Multiplexing (DWDM) Networks";
       }
     }

     grouping transceiver-mode {
       description
         "This grouping is intended to be used for reporting the
         information of a transceiver's mode.

         The attributes for the explicit mode shall be augmented when
         used with either:
         - the proper leafrefs, when explicit mode templates are used;
           or,
         - the explicit-mode grouping, when explicit mode templates
           are not used.

         The compatible-modes container shall be augmented with the
         proper leafrefs when used: see for example the
         transceiver-capabilities grouping below.";
       choice mode {
         config false;
         mandatory true;
         description
           "Indicates whether the transceiver's mode is a standard
             mode, an organizational mode or an explicit mode.";
         case G.698.2 {
           uses standard-mode;
           uses common-standard-organizational-mode;
           uses common-all-modes;
         }
         case organizational-mode {
           container organizational-mode {
             config false;
             description
               "The set of attributes for an organizational mode";
             uses organizational-mode;
             uses common-standard-organizational-mode;
             uses common-all-modes;
           }  // container organizational-mode
         }
         case explicit-mode {
           container explicit-mode {
             config false;
             description
               "The set of attributes for an explicit mode";
             // uses explicit-mode;
             uses common-all-modes;



Belotti, et al.            Expires 7 June 2025                 [Page 42]

Internet-Draft            L0 Common YANG Types             December 2024


             container compatible-modes {
               description
                 "Container for all the standard and organizational
                   modes supported by the transceiver's explicit
                   mode.";
             }  // container compatible-modes
           }  // container explicit-mode
         } // end of case explicit-mode
       } // end of choice
     }

     grouping transceiver-capabilities {
       description
         "This grouping is intended to be used for reporting the
         capabilities of a transceiver.

         The attributes for the explicit mode shall be augmented when
         used with either:
         - the proper leafrefs, when explicit mode templates are used;
           or,
         - the explicit-mode grouping, when explicit mode templates
           are not used.";

       container supported-modes {
         presence
           "When present, it indicates that the modes supported by a
           transceiver are reported.";
         config false;
         description
           "The top level container for the list supported
           transceiver's modes.";
         list supported-mode {
           key "mode-id";
           config false;
           min-elements 1;
           description "The list of supported transceiver's modes.";
           leaf mode-id {
             type string {
               length "1..255";
             }
             description "ID for the supported transceiver's mode.";
           }
           uses transceiver-mode {
             augment "mode/explicit-mode/explicit-mode/"
                   + "compatible-modes" {
               description
                 "Augments the compatible modes with the proper
                 leafrefs.";



Belotti, et al.            Expires 7 June 2025                 [Page 43]

Internet-Draft            L0 Common YANG Types             December 2024


               leaf-list supported-application-codes {
                 type leafref {
                   path "../../../../supported-mode/mode-id";
                 }
                 must "../../../../"
                     + "supported-mode[mode-id=current()]/"
                     + "standard-mode" {
                   description
                     "The pointer is only for application codes
                     supported by transceiver.";
                 }
                 description
                   "List of pointers to the application codes
                   supported by the transceiver's explicit mode.";
               }
               leaf-list supported-organizational-modes {
                 type leafref {
                   path "../../../../supported-mode/mode-id";
                 }
                 must "../../../../"
                     + "supported-mode[mode-id=current()]/"
                     + "organizational-mode" {
                   description
                     "The pointer is only for organizational modes
                     supported by transceiver.";
                 }
                 description
                   "List of pointers to the organizational modes
                     supported by the transceiver's explicit mode.";
               }
             }
           }
         }  // list supported-modes
       }  // container supported-modes
     }  // grouping transceiver-capabilities

     grouping standard-mode {
       description
         "ITU-T G.698.2 standard mode that guarantees interoperability.
          It must be an string with the following format:
          B-DScW-ytz(v) where all these attributes are conformant
          to the ITU-T recomendation";

       leaf standard-mode {
         type standard-mode;
         config false;
         description
           "G.698.2 standard mode";



Belotti, et al.            Expires 7 June 2025                 [Page 44]

Internet-Draft            L0 Common YANG Types             December 2024


       }
     }

     grouping organizational-mode {
       description
         "Transponder operational mode supported by organizations or
          vendor";

       leaf operational-mode {
         type operational-mode;
         config false;
         description
           "configured organization- or vendor-specific
            application identifiers (AI) supported by the transponder";
       }
       leaf organization-identifier {
         type organization-identifier;
         config false;
         description
           "organization identifier that uses organizational
            mode";
       }
     }

     grouping penalty-value {
       description
         "A common definition of the penalty value used for describing
         multiple penalty types (.e.g, CD, PMD, PDL).";

       leaf penalty-value {
         type union {
           type decimal-2 {
             range "0..max";
           }
           type empty;
         }
         units "dB";
         config false;
         mandatory true;
         description
           "The OSNR penalty associated with the related optical
           impairment at the receiver, when the value is known or an
           empty value when the value is not known.";
       }
     }

     grouping explicit-mode {
       description



Belotti, et al.            Expires 7 June 2025                 [Page 45]

Internet-Draft            L0 Common YANG Types             December 2024


         "Attributes capabilities related to explicit transceiver's
         mode.

         This grouping also contains the list of attributes related to
         optical impairment limits for explicit mode (min OSNR, max PMD,
         max CD, max PDL, Q-factor limit, etc.).

         In case of standard and operational mode the attributes are
         implicit.";
       leaf line-coding-bitrate {
         type identityref {
           base line-coding;
         }
         config false;
         description
           "Bit rate/line coding of the optical tributary signal.";
         reference
           "ITU-T G.698.2 section 7.1.2";
       }
       leaf bitrate {
         type uint16;
         units "Gbit/sec";
         config false;
         description
           "The gross bitrate (e.g., 100, 200) of the optical tributary
           signal.";
       }
       leaf max-diff-group-delay  {
         type decimal-2;
         units "ps";
         config false;
         description
           "Maximum Differential group delay of this mode for this
           lane";
       }
       leaf max-chromatic-dispersion {
         type decimal-2 {
           range "0..max";
         }
         units "ps/nm";
         config false;
         description
           "Maximum acceptable accumulated chromatic dispersion (CD)
           on the receiver";
       }
       list cd-penalty {
         key cd-value;
         config false;



Belotti, et al.            Expires 7 June 2025                 [Page 46]

Internet-Draft            L0 Common YANG Types             December 2024


         description
           "Optional penalty associated with a given accumulated
           chromatic dispersion (CD) value.

           This list of pair CD and penalty values can be used to
           sample the function penalty = f(CD).";
         leaf cd-value {
           type decimal-2;
           units "ps/nm";
           config false;
           mandatory true;
           description
             "The Chromatic Dispersion (CD).";
         }
         uses penalty-value;
       }
       leaf max-polarization-mode-dispersion {
         type decimal-2 {
           range "0..max";
         }
         units "ps";
         config false;
         description
           "Maximum acceptable accumulated polarization mode
            dispersion (PMD) on the receiver";
         reference
           "ITU-T G.666 (02/2011): Characteristics of polarization
           mode dispersion compensators and of receivers that
           compensate for polarization mode dispersion";
       }
       list pmd-penalty {
         key pmd-value;
         config false;
         description
           "Optional penalty associated with a given accumulated
           polarization mode dispersion (PMD) value.

           This list of pair PMD and penalty can be used to
           sample the function penalty = f(PMD).";
         leaf pmd-value {
           type decimal-2 {
             range "0..max";
           }
           units "ps";
           config false;
           mandatory true;
           description
             "The Polarization Mode Dispersion (PMD).";



Belotti, et al.            Expires 7 June 2025                 [Page 47]

Internet-Draft            L0 Common YANG Types             December 2024


         }
         uses penalty-value;
       }
       leaf max-polarization-dependent-loss {
         type power-loss-or-null;
         config false;
         mandatory true;
         description
           "Maximum acceptable accumulated accumulated polarization
           dependent loss (PDL) on the receiver";
       }
       list pdl-penalty {
         key pdl-value;
         config false;
         description
           "Optional penalty associated with a given accumulated
           polarization dependent loss (PDL) value.

           This list of pair PDL and penalty values can be used to
           sample the function PDL = f(penalty).";
         leaf pdl-value {
           type power-loss;
           config false;
           mandatory true;
           description
             "Maximum acceptable accumulated polarization dependent
             loss (PDL).";
         }
         uses penalty-value;
       }
       leaf available-modulation-type {
         type identityref {
           base modulation;
         }
         config false;
         description
           "Modulation type the specific transceiver in the list
            can support";
       }
       leaf min-OSNR {
         type snr;
         units "dBm";
         config false;
         description
           "min OSNR measured over 0.1 nm resolution bandwidth:
           if received OSNR at Rx-power reference point
           (rx-ref-channel-power) is lower than MIN-OSNR, an increased
           level of bit-errors post-FEC needs to be expected";



Belotti, et al.            Expires 7 June 2025                 [Page 48]

Internet-Draft            L0 Common YANG Types             December 2024


       }
       leaf rx-ref-channel-power {
         type power-dbm;
         config false;
         description
           "The channel power used as reference for defining penalties
           and min-OSNR";
       }
       list rx-channel-power-penalty {
         key rx-channel-power-value;
         config false;
         description
           "Optional penalty associated with a received power
           lower than rx-ref-channel-power.

           This list of pair power and penalty can be used to
           sample the function penalty = f(rx-channel-power).";
         leaf rx-channel-power-value {
           type power-dbm;
           units "dBm";
           config false;
           mandatory true;
           description
             "The Received Power.";
         }
         uses penalty-value;
       }
       leaf min-Q-factor {
         type decimal-2;
         units "dB";
         config false;
         description "min Qfactor at FEC threshold";
       }
       leaf available-baud-rate {
         type decimal64 {
           fraction-digits 1;
         }
         units "Bd";
         config false;
         description
           "Baud-rate the specific transceiver in
           the list can support.
            Baud-rate is the unit for
            symbol rate or modulation rate
            in symbols per second or
            pulses per second.
            It is the number of distinct symbol
            changes (signal events) made to the



Belotti, et al.            Expires 7 June 2025                 [Page 49]

Internet-Draft            L0 Common YANG Types             December 2024


            transmission medium
            per second in a digitally
            modulated signal or a line code";
       }
       leaf roll-off {
         type decimal64 {
           fraction-digits 4;
           range "0..1";
         }
         config false;
         description
           "the roll-off factor (beta with values from 0 to 1)
           identifies how the real signal shape exceed
           the baud rate. If=0 it is exactly matching
           the baud rate.If=1 the signal exceeds the
           50% of the baud rate at each side.";
       }
       leaf min-carrier-spacing {
         type frequency-ghz;
         config false;
         description
           "This attribute specifies the minimum nominal difference
           between the carrier frequencies of two homogeneous OTSis
           (which have the same optical characteristics but the central
           frequencies) such that if they are placed next to each other
           the interference due to spectrum overlap between them can be
           considered negligible.

           In case of heterogeneous OTSi it is up to path computation
           engine to determine the minimum distance between the carrier
           frequency of the two adjacent OTSi.";
       }
       leaf available-fec-type {
         type identityref {
           base fec-type;
         }
         config false;
         description "Available FEC";
       }
       leaf fec-code-rate {
         type decimal64 {
           fraction-digits 8;
           range "0..max";
         }
         config false;
         description "FEC-code-rate";
       }
       leaf fec-threshold {



Belotti, et al.            Expires 7 June 2025                 [Page 50]

Internet-Draft            L0 Common YANG Types             December 2024


         type decimal64 {
           fraction-digits 8;
           range "0..max";
         }
         config false;
         description
           "Threshold on the BER, for which FEC
            is able to correct errors";
       }
       leaf in-band-osnr {
         type snr;
         config false;
         description
           "The OSNR defined within the bandwidth of the transmit
           spectral excursion (i.e.,  between the nominal central
           frequency of the channel and the -3.0dB points of the
           transmitter spectrum furthest from the nominal central
           frequency) measured at reference point Ss.

           The in-band OSNR is referenced to an optical bandwidth of
           0.1nm @ 193.7 THz or 12.5 GHz.";
         reference
           "OIF-400ZR-01.0: Implementation Agreement 400ZR";
       }
       leaf out-of-band-osnr {
         type snr;
         config false;
         description
           "The ratio of the peak transmitter power to the integrated
           power outside the transmitter spectral excursion.

           The spectral resolution of the measurement shall be better
           than the maximum spectral width of the peak.

           The out-of-band OSNR is referenced to an optical bandwidth
           of 0.1nm @ 193.7 THz or 12.5 GHz";
         reference
           "OIF-400ZR-01.0: Implementation Agreement 400ZR";
       }
       leaf tx-polarization-power-difference {
         type power-ratio;
         config false;
         description
           "The transmitter polarization dependent power difference
           defined as the power difference between X and Y
           polarizations";
         reference
           "OIF-400ZR-01.0: Implementation Agreement 400ZR";



Belotti, et al.            Expires 7 June 2025                 [Page 51]

Internet-Draft            L0 Common YANG Types             December 2024


       }
       leaf polarization-skew {
         type decimal-2;
         units "ps";
         config false;
         description
           "The X-Y skew, included as a fixed value in the receiver
           polarization mode dispersion (PMD) tolerance limits.";
         reference
           "OIF-400ZR-01.0: Implementation Agreement 400ZR";
       }
     } // grouping explicit-mode

     grouping common-standard-organizational-mode {
       description
         "Common attributes used by standard and organizational
         transceiver's modes.";

       leaf-list line-coding-bitrate {
         type identityref {
           base line-coding;
         }
         config false;
         description
           "The list of the bit rate/line coding of the optical
           tributary signal supported by the transceiver.

           Reporting this list is optional when the standard or
           organization mode supports only one bit rate/line coding.";
         reference
           "ITU-T G.698.2 section 7.1.2";
       }
     } // grouping common-standard-organizational-mode

     grouping transmitter-tuning-range {
       description
         "Transmitter tuning range (f_tx-min, f_tx-max)";

       leaf min-central-frequency {
         type frequency-thz;
         description
           "This parameter indicates the minimum frequency for the
           transmitter tuning range.";
       }
       leaf max-central-frequency {
         type frequency-thz;
         description
           "This parameter indicates the maximum frequency for the



Belotti, et al.            Expires 7 June 2025                 [Page 52]

Internet-Draft            L0 Common YANG Types             December 2024


           transmitter tuning range.";
       }

       leaf transceiver-tunability {
         type frequency-ghz;
         description
           "This parameter indicates the transmitter frequency fine
           tuning steps e.g 3.125GHz or 0.001GHz.";
       }
     } // grouping transmitter-tuning-range

     grouping common-all-modes {
       description
         "Common attributes used by all transceiver's modes.";

       container transmitter-tuning-range {
         config false;
         description
           "Transmitter tuning range (f_tx-min, f_tx-max)";
         uses transmitter-tuning-range;
       }
   /* Alternative solution (not future safe):

       uses transmitter-tuning-range {
         refine min-central-frequency {
           config false;
         }
         refine max-central-frequency {
           config false;
         }
         refine transceiver-tunability {
           config false;
         }
       }
   */
       leaf tx-channel-power-min {
         type power-dbm;
         config false;
         description "The minimum output power of this interface";
       }
       leaf tx-channel-power-max {
         type power-dbm;
         config false;
         description "The maximum output power of this interface";
       }
       leaf rx-channel-power-min {
         type power-dbm;
         config false;



Belotti, et al.            Expires 7 June 2025                 [Page 53]

Internet-Draft            L0 Common YANG Types             December 2024


         description "The minimum input power of this interface";
       }
       leaf rx-channel-power-max {
         type power-dbm;
         config false;
         description "The maximum input power of this interface";
       }
       leaf rx-total-power-max {
         type power-dbm;
         config false;
         description
           "Maximum rx optical power for all the channels.

           It is applicable only to multi-channel modes.";
       }
     } // grouping common-all-modes

     grouping common-transceiver-param {
       description
         "The common parameters of an optical transceiver,
         that supplement the configured mode.";

       uses common-transceiver-configured-param;
       uses common-transceiver-readonly-param;
     }

     grouping common-transceiver-configured-param {
       description
         "The configured parameters of an optical transceiver,
         that supplement the configured mode.";

       leaf line-coding-bitrate {
         type identityref {
           base line-coding;
         }
         description
           "Bit rate/line coding of the optical tributary signal.

           Support of this attribute is optional when the configured
           mode supports only one bit rate/line coding.";
         reference
           "ITU-T G.698.2 section 7.1.2";
       }
       leaf tx-channel-power {
         type power-dbm-or-null;
         description
           "The current channel transmit power, when the value is
           known or an empty value when the value is not known.



Belotti, et al.            Expires 7 June 2025                 [Page 54]

Internet-Draft            L0 Common YANG Types             December 2024


           The empty value MUST NOT be used when this attribute is
           configured.";
       }
     } // grouping for configured transceiver attributes out of mode

     grouping common-transceiver-readonly-param {
       description
         "The common read-only parameters of an optical transceiver,
         that supplement the configured mode.";

       leaf rx-channel-power {
         type power-dbm-or-null;
         config false;
         description
           "The current channel received power, when the value is
           known or an empty value when the value is not known.";
       }
       leaf rx-total-power {
         type power-dbm-or-null;
         config false;
         description
           "The current total received power, when the value is known
           or an empty value when the value is not known.";
       }
     } // grouping for read-only transceiver attributes out of mode

     grouping l0-tunnel-attributes {
       description
         "Parameters for Layer0 (WSON or Flexi-Grid) Tunnels.";

       leaf wavelength-assignment {
         type identityref {
           base wavelength-assignment;
         }
         description "Wavelength Allocation Method";
       }
     }

     grouping frequency-range {
       description
         "This grouping defines the lower and upper bounds of a
         frequency range (e.g., a band).

         This grouping SHOULD NOT be used to define a frequency slot,
         which SHOULD be defined using the n and m values instead.";
       leaf lower-frequency {
         type frequency-thz;
         mandatory true;



Belotti, et al.            Expires 7 June 2025                 [Page 55]

Internet-Draft            L0 Common YANG Types             December 2024


         description
           "The lower frequency boundary of the
           frequency range.";
       }
       leaf upper-frequency {
         type frequency-thz;
         must '. > ../lower-frequency' {
           error-message
             "The upper frequency must be greater than the lower
             frequency.";
         }
         mandatory true;
         description
           "The upper frequency boundary of the
           frequency range.";
       }
     }

     grouping l0-path-constraints {
       description
         "Common attribute for Layer 0 path constraints to be used by
         Layer 0 computation.";
       leaf gsnr-extra-margin {
         type snr {
           range 0..max;
         }
         default 0;
         description
           "An additional margin to be added to the OSNR-min of the
           transceiver when checking the estimated received Generalized
           SNR (GSNR).";
       }
     }

     grouping l0-path-properties {
       description
         "Common attribute for reporting the Layer 0 computed path
         properties.";
       leaf estimated-gsnr {
         type snr;
         config false;
         description
           "The estimate received GSNR for the computed path.";
       }
       leaf estimated-eol-gsnr {
         type snr;
         config false;
         description



Belotti, et al.            Expires 7 June 2025                 [Page 56]

Internet-Draft            L0 Common YANG Types             December 2024


           "The estimate received GSNR for the computed path
            degraded at the end of life.";
       }
       leaf estimated-lowest-gsnr {
         type snr;
         config false;
         description
           "The estimate lowest received GSNR for the computed path
            among all possible wavelength channels along the same
            path.";
       }
     }
   }
   <CODE ENDS>

                    Figure 1: Layer 0 Types YANG module

4.  Security Considerations

   This section is modeled after the template described in Section 3.7
   of [I-D.ietf-netmod-rfc8407bis].

   The "ietf-layer0-types" YANG module define data models that are
   designed to be accessed via YANG-based management protocols, such as
   NETCONF [RFC6241] and RESTCONF [RFC8040].  These protocols have to
   use a secure transport layer (e.g., SSH [RFC4252], TLS [RFC8446], and
   QUIC [RFC9000]) and have to use mutual authentication.

   The Network Configuration Access Control Model (NACM) [RFC8341]
   provides the means to restrict access for particular NETCONF or
   RESTCONF users to a preconfigured subset of all available NETCONF or
   RESTCONF protocol operations and content.

   The YANG modules define a set of identities, types, and groupings.
   These nodes are intended to be reused by other YANG modules.  The
   modules by themselves do not expose any data nodes that are writable,
   data nodes that contain read-only state, or RPCs.  As such, there are
   no additional security issues related to the YANG module that need to
   be considered.

   Modules that use the groupings that are defined in this document
   should identify the corresponding security considerations.  For
   example, reusing some of these groupings will expose privacy-related
   information (e.g., 'node-example').







Belotti, et al.            Expires 7 June 2025                 [Page 57]

Internet-Draft            L0 Common YANG Types             December 2024


5.  IANA Considerations

   This document requests IANA to update the following URIs in the "IETF
   XML Registry" [RFC3688] to refer to this document:

      URI:  urn:ietf:params:xml:ns:yang:ietf-layer0-types
      Registrant Contact:  The IESG
      XML:  N/A; the requested URI is an XML namespace.

   This document requests IANA to register the following YANG modules in
   the "YANG Module Names" registry [RFC6020] within the "YANG
   Parameters" registry group.

      Name:  ietf-layer0-types
      Maintained by IANA?  N
      Namespace:  urn:ietf:params:xml:ns:yang:ietf-layer0-types
      Prefix:  l0-types
      Reference:  RFC XXXX

      RFC Editor Note: Please replace XXXX with the RFC number assigned
      to this document and remove this note.

6.  References

6.1.  Normative References

   [I-D.ietf-ccamp-optical-impairment-topology-yang]
              Beller, D., Le Rouzic, E., Belotti, S., Galimberti, G.,
              and I. Busi, "A YANG Data Model for Optical Impairment-
              aware Topology", Work in Progress, Internet-Draft, draft-
              ietf-ccamp-optical-impairment-topology-yang-17, 21 October
              2024, <https://datatracker.ietf.org/doc/html/draft-ietf-
              ccamp-optical-impairment-topology-yang-17>.

   [I-D.ietf-teas-rfc8776-update]
              Busi, I., Guo, A., Liu, X., Saad, T., and I. Bryskin,
              "Common YANG Data Types for Traffic Engineering", Work in
              Progress, Internet-Draft, draft-ietf-teas-rfc8776-update-
              14, 4 November 2024,
              <https://datatracker.ietf.org/doc/html/draft-ietf-teas-
              rfc8776-update-14>.

   [ITU-T_G.666]
              International Telecommunication Union, "Characteristics of
              polarization mode dispersion compensators and of receivers
              that compensate for polarization mode dispersion"", ITU-T
              Recommendation G.666 , February 2011,
              <https://www.itu.int/rec/T-REC-G.666>.



Belotti, et al.            Expires 7 June 2025                 [Page 58]

Internet-Draft            L0 Common YANG Types             December 2024


   [ITU-T_G.694.1]
              International Telecommunication Union, "Spectral grids for
              WDM applications: DWDM frequency grid", ITU-T
              Recommendation G.694.1 , October 2020,
              <https://www.itu.int/rec/T-REC-G.694.1>.

   [ITU-T_G.694.2]
              International Telecommunication Union, "Spectral grids for
              WDM applications: CWDM wavelength grid", ITU-T
              Recommendation G.694.2 , December 2003,
              <https://www.itu.int/rec/T-REC-G.694.2>.

   [ITU-T_G.698.2]
              International Telecommunication Union, "Amplified
              multichannel dense wavelength division multiplexing
              applications with single channel optical interfaces",
              ITU-T Recommendation G.698.2 , November 2018,
              <https://www.itu.int/rec/T-REC-G.698.2>.

   [ITU-T_G.709]
              International Telecommunication Union, "Interfaces for the
              optical transport network", ITU-T Recommendation G.709 ,
              June 2020, <https://www.itu.int/rec/T-REC-G.709>.

   [ITU-T_G.709.2]
              International Telecommunication Union, "OTU4 long-reach
              interface", ITU-T Recommendation G.709.2, Corrigendum 1 ,
              September 2020, <https://www.itu.int/rec/T-REC-G.709.2>.

   [ITU-T_G.709.3]
              International Telecommunication Union, "Flexible OTN B100G
              long-reach interfaces", ITU-T Recommendation G.709.3,
              Amendment 1 , November 2022,
              <https://www.itu.int/rec/T-REC-G.709.3>.

   [ITU-T_G.959.1]
              International Telecommunication Union, "Optical transport
              network physical layer interfaces", ITU-T Recommendation
              G.959.1 , July 2018,
              <https://www.itu.int/rec/T-REC-G.959.1>.

   [ITU-T_G.9700]
              International Telecommunication Union, "Fast access to
              subscriber terminals (G.fast) - Power spectral density
              specification", ITU-T Recommendation G.9700 , July 2019,
              <https://www.itu.int/rec/T-REC-G.9700>.





Belotti, et al.            Expires 7 June 2025                 [Page 59]

Internet-Draft            L0 Common YANG Types             December 2024


   [ITU-T_G.975]
              International Telecommunication Union, "Forward error
              correction for submarine systems", ITU-T Recommendation
              G.975 , October 2000,
              <https://www.itu.int/rec/T-REC-G.975>.

   [ITU-T_G.975.1]
              International Telecommunication Union, "Forward error
              correction for high bit-rate DWDM submarine systems",
              ITU-T Recommendation G.975.1, Corrigendum 2 , July 2013,
              <https://www.itu.int/rec/T-REC-G.975.1>.

   [ITU-T_G.977.1]
              International Telecommunication Union, "Transverse
              compatible dense wavelength division multiplexing
              applications for repeatered optical fibre submarine cable
              systems", ITU-T Recommendation G.977.1 , February 2021,
              <https://www.itu.int/rec/T-REC-G.977.1>.

   [OIF_400ZR]
              Optical Internetworking Forum, "Implementation Agreement
              400ZR", OIF-400ZR-01.0 Implementation Agreement , March
              2020, <https://www.oiforum.com/wp-content/uploads/OIF-
              400ZR-01.0_reduced2.pdf>.

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <https://www.rfc-editor.org/rfc/rfc2119>.

   [RFC3471]  Berger, L., Ed., "Generalized Multi-Protocol Label
              Switching (GMPLS) Signaling Functional Description",
              RFC 3471, DOI 10.17487/RFC3471, January 2003,
              <https://www.rfc-editor.org/rfc/rfc3471>.

   [RFC4203]  Kompella, K., Ed. and Y. Rekhter, Ed., "OSPF Extensions in
              Support of Generalized Multi-Protocol Label Switching
              (GMPLS)", RFC 4203, DOI 10.17487/RFC4203, October 2005,
              <https://www.rfc-editor.org/rfc/rfc4203>.

   [RFC6020]  Bjorklund, M., Ed., "YANG - A Data Modeling Language for
              the Network Configuration Protocol (NETCONF)", RFC 6020,
              DOI 10.17487/RFC6020, October 2010,
              <https://www.rfc-editor.org/rfc/rfc6020>.







Belotti, et al.            Expires 7 June 2025                 [Page 60]

Internet-Draft            L0 Common YANG Types             December 2024


   [RFC6205]  Otani, T., Ed. and D. Li, Ed., "Generalized Labels for
              Lambda-Switch-Capable (LSC) Label Switching Routers",
              RFC 6205, DOI 10.17487/RFC6205, March 2011,
              <https://www.rfc-editor.org/rfc/rfc6205>.

   [RFC6241]  Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed.,
              and A. Bierman, Ed., "Network Configuration Protocol
              (NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011,
              <https://www.rfc-editor.org/rfc/rfc6241>.

   [RFC7688]  Lee, Y., Ed. and G. Bernstein, Ed., "GMPLS OSPF
              Enhancement for Signal and Network Element Compatibility
              for Wavelength Switched Optical Networks", RFC 7688,
              DOI 10.17487/RFC7688, November 2015,
              <https://www.rfc-editor.org/rfc/rfc7688>.

   [RFC7689]  Bernstein, G., Ed., Xu, S., Lee, Y., Ed., Martinelli, G.,
              and H. Harai, "Signaling Extensions for Wavelength
              Switched Optical Networks", RFC 7689,
              DOI 10.17487/RFC7689, November 2015,
              <https://www.rfc-editor.org/rfc/rfc7689>.

   [RFC7698]  Gonzalez de Dios, O., Ed., Casellas, R., Ed., Zhang, F.,
              Fu, X., Ceccarelli, D., and I. Hussain, "Framework and
              Requirements for GMPLS-Based Control of Flexi-Grid Dense
              Wavelength Division Multiplexing (DWDM) Networks",
              RFC 7698, DOI 10.17487/RFC7698, November 2015,
              <https://www.rfc-editor.org/rfc/rfc7698>.

   [RFC7699]  Farrel, A., King, D., Li, Y., and F. Zhang, "Generalized
              Labels for the Flexi-Grid in Lambda Switch Capable (LSC)
              Label Switching Routers", RFC 7699, DOI 10.17487/RFC7699,
              November 2015, <https://www.rfc-editor.org/rfc/rfc7699>.

   [RFC7950]  Bjorklund, M., Ed., "The YANG 1.1 Data Modeling Language",
              RFC 7950, DOI 10.17487/RFC7950, August 2016,
              <https://www.rfc-editor.org/rfc/rfc7950>.

   [RFC8174]  Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
              2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
              May 2017, <https://www.rfc-editor.org/rfc/rfc8174>.

   [RFC8341]  Bierman, A. and M. Bjorklund, "Network Configuration
              Access Control Model", STD 91, RFC 8341,
              DOI 10.17487/RFC8341, March 2018,
              <https://www.rfc-editor.org/rfc/rfc8341>.





Belotti, et al.            Expires 7 June 2025                 [Page 61]

Internet-Draft            L0 Common YANG Types             December 2024


   [RFC8342]  Bjorklund, M., Schoenwaelder, J., Shafer, P., Watsen, K.,
              and R. Wilton, "Network Management Datastore Architecture
              (NMDA)", RFC 8342, DOI 10.17487/RFC8342, March 2018,
              <https://www.rfc-editor.org/rfc/rfc8342>.

   [RFC8363]  Zhang, X., Zheng, H., Casellas, R., Gonzalez de Dios, O.,
              and D. Ceccarelli, "GMPLS OSPF-TE Extensions in Support of
              Flexi-Grid Dense Wavelength Division Multiplexing (DWDM)
              Networks", RFC 8363, DOI 10.17487/RFC8363, May 2018,
              <https://www.rfc-editor.org/rfc/rfc8363>.

   [RFC8795]  Liu, X., Bryskin, I., Beeram, V., Saad, T., Shah, H., and
              O. Gonzalez de Dios, "YANG Data Model for Traffic
              Engineering (TE) Topologies", RFC 8795,
              DOI 10.17487/RFC8795, August 2020,
              <https://www.rfc-editor.org/rfc/rfc8795>.

   [RFC9093]  Zheng, H., Lee, Y., Guo, A., Lopez, V., and D. King, "A
              YANG Data Model for Layer 0 Types", RFC 9093,
              DOI 10.17487/RFC9093, August 2021,
              <https://www.rfc-editor.org/rfc/rfc9093>.

6.2.  Informative References

   [I-D.ietf-netmod-rfc8407bis]
              Bierman, A., Boucadair, M., and Q. Wu, "Guidelines for
              Authors and Reviewers of Documents Containing YANG Data
              Models", Work in Progress, Internet-Draft, draft-ietf-
              netmod-rfc8407bis-21, 13 November 2024,
              <https://datatracker.ietf.org/doc/html/draft-ietf-netmod-
              rfc8407bis-21>.

   [ITU-T_G.Sup39]
              International Telecommunication Union, "Optical system
              design and engineering considerations", ITU-T Supplement
              G.Sup39 , February 2016.

   [RFC3688]  Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688,
              DOI 10.17487/RFC3688, January 2004,
              <https://www.rfc-editor.org/rfc/rfc3688>.

   [RFC4252]  Ylonen, T. and C. Lonvick, Ed., "The Secure Shell (SSH)
              Authentication Protocol", RFC 4252, DOI 10.17487/RFC4252,
              January 2006, <https://www.rfc-editor.org/rfc/rfc4252>.







Belotti, et al.            Expires 7 June 2025                 [Page 62]

Internet-Draft            L0 Common YANG Types             December 2024


   [RFC6163]  Lee, Y., Ed., Bernstein, G., Ed., and W. Imajuku,
              "Framework for GMPLS and Path Computation Element (PCE)
              Control of Wavelength Switched Optical Networks (WSONs)",
              RFC 6163, DOI 10.17487/RFC6163, April 2011,
              <https://www.rfc-editor.org/rfc/rfc6163>.

   [RFC7446]  Lee, Y., Ed., Bernstein, G., Ed., Li, D., and W. Imajuku,
              "Routing and Wavelength Assignment Information Model for
              Wavelength Switched Optical Networks", RFC 7446,
              DOI 10.17487/RFC7446, February 2015,
              <https://www.rfc-editor.org/rfc/rfc7446>.

   [RFC7581]  Bernstein, G., Ed., Lee, Y., Ed., Li, D., Imajuku, W., and
              J. Han, "Routing and Wavelength Assignment Information
              Encoding for Wavelength Switched Optical Networks",
              RFC 7581, DOI 10.17487/RFC7581, June 2015,
              <https://www.rfc-editor.org/rfc/rfc7581>.

   [RFC8040]  Bierman, A., Bjorklund, M., and K. Watsen, "RESTCONF
              Protocol", RFC 8040, DOI 10.17487/RFC8040, January 2017,
              <https://www.rfc-editor.org/rfc/rfc8040>.

   [RFC8340]  Bjorklund, M. and L. Berger, Ed., "YANG Tree Diagrams",
              BCP 215, RFC 8340, DOI 10.17487/RFC8340, March 2018,
              <https://www.rfc-editor.org/rfc/rfc8340>.

   [RFC8446]  Rescorla, E., "The Transport Layer Security (TLS) Protocol
              Version 1.3", RFC 8446, DOI 10.17487/RFC8446, August 2018,
              <https://www.rfc-editor.org/rfc/rfc8446>.

   [RFC9000]  Iyengar, J., Ed. and M. Thomson, Ed., "QUIC: A UDP-Based
              Multiplexed and Secure Transport", RFC 9000,
              DOI 10.17487/RFC9000, May 2021,
              <https://www.rfc-editor.org/rfc/rfc9000>.

Appendix A.  The Complete Schema Trees

   This appendix presents the complete tree of the Layer 0 Types data
   model.  See [RFC8340] for an explanation of the symbols used.  The
   data type of every leaf node is shown near the right end of the
   corresponding line.

   module: ietf-layer0-types

     grouping wdm-label-start-end:
       +-- (grid-type)?
          +--:(fixed-dwdm)
          |  +-- dwdm-n?    l0-types:dwdm-n



Belotti, et al.            Expires 7 June 2025                 [Page 63]

Internet-Draft            L0 Common YANG Types             December 2024


          +--:(cwdm)
          |  +-- cwdm-n?    l0-types:cwdm-n
          +--:(flexi-grid)
             +-- flexi-n?   l0-types:flexi-n
     grouping wdm-label-step:
       +-- (l0-grid-type)?
          +--:(fixed-dwdm)
          |  +-- wson-dwdm-channel-spacing?    identityref
          +--:(cwdm)
          |  +-- wson-cwdm-channel-spacing?    identityref
          +--:(flexi-grid)
             x-- flexi-grid-channel-spacing?   identityref
             +-- flexi-ncfg?                   identityref
             +-- flexi-n-step?                 uint8
     grouping wdm-label-hop:
       +-- (grid-type)?
          +--:(fixed-dwdm)
          |  +-- (fixed-single-or-super-channel)?
          |     +--:(single)
          |     |  +-- dwdm-n?               l0-types:dwdm-n
          |     +--:(multi)
          |        +-- subcarrier-dwdm-n*    l0-types:dwdm-n
          +--:(cwdm)
          |  +-- cwdm-n?                     l0-types:cwdm-n
          +--:(flexi-grid)
             +-- (single-or-super-channel)?
                +--:(single)
                |  +-- flexi-n?              l0-types:flexi-n
                |  +-- flexi-m?              l0-types:flexi-m
                x--:(super)
                |  x-- subcarrier-flexi-n* [flexi-n]
                |     +-- flexi-n?   l0-types:flexi-n
                |     +-- flexi-m?   l0-types:flexi-m
                +--:(multi)
                   +-- frequency-slots
                      +-- frequency-slot* [flexi-n]
                         +-- flexi-n?   l0-types:flexi-n
                         +-- flexi-m?   l0-types:flexi-m
     grouping wdm-label-range-info:
       +-- grid-type?    identityref
       +-- priority?     uint8
       +-- flexi-grid
          +-- slot-width-granularity?   identityref
          +-- min-slot-width-factor?    uint16
          +-- max-slot-width-factor?    uint16
     grouping wson-label-start-end:
       +-- (grid-type)?
          +--:(dwdm)



Belotti, et al.            Expires 7 June 2025                 [Page 64]

Internet-Draft            L0 Common YANG Types             December 2024


          |  +-- dwdm-n?   l0-types:dwdm-n
          +--:(cwdm)
             +-- cwdm-n?   l0-types:cwdm-n
     grouping wson-label-hop:
       +-- (grid-type)?
          +--:(dwdm)
          |  +-- (single-or-super-channel)?
          |     +--:(single)
          |     |  +-- dwdm-n?              l0-types:dwdm-n
          |     +--:(super)
          |        +-- subcarrier-dwdm-n*   l0-types:dwdm-n
          +--:(cwdm)
             +-- cwdm-n?                    l0-types:cwdm-n
     grouping l0-label-range-info:
       +-- grid-type?   identityref
       +-- priority?    uint8
     grouping wson-label-step:
       +-- (l0-grid-type)?
          +--:(dwdm)
          |  +-- wson-dwdm-channel-spacing?   identityref
          +--:(cwdm)
             +-- wson-cwdm-channel-spacing?   identityref
     grouping flexi-grid-label-start-end:
       +-- flexi-n?   l0-types:flexi-n
     grouping flexi-grid-frequency-slot:
       +-- flexi-n?   l0-types:flexi-n
       +-- flexi-m?   l0-types:flexi-m
     grouping flexi-grid-label-hop:
       +-- (single-or-super-channel)?
          +--:(single)
          |  +-- flexi-n?              l0-types:flexi-n
          |  +-- flexi-m?              l0-types:flexi-m
          x--:(super)
          |  x-- subcarrier-flexi-n* [flexi-n]
          |     +-- flexi-n?   l0-types:flexi-n
          |     +-- flexi-m?   l0-types:flexi-m
          +--:(multi)
             +-- frequency-slots
                +-- frequency-slot* [flexi-n]
                   +-- flexi-n?   l0-types:flexi-n
                   +-- flexi-m?   l0-types:flexi-m
     grouping flexi-grid-label-range-info:
       +-- grid-type?    identityref
       +-- priority?     uint8
       +-- flexi-grid
          +-- slot-width-granularity?   identityref
          +-- min-slot-width-factor?    uint16
          +-- max-slot-width-factor?    uint16



Belotti, et al.            Expires 7 June 2025                 [Page 65]

Internet-Draft            L0 Common YANG Types             December 2024


     grouping flexi-grid-label-step:
       x-- flexi-grid-channel-spacing?   identityref
       +-- flexi-ncfg?                   identityref
       +-- flexi-n-step?                 uint8
     grouping transceiver-mode:
       +--ro (mode)
          +--:(G.698.2)
          |  +--ro standard-mode?              standard-mode
          |  +--ro line-coding-bitrate*        identityref
          |  +--ro transmitter-tuning-range
          |  |  +--ro min-central-frequency?    frequency-thz
          |  |  +--ro max-central-frequency?    frequency-thz
          |  |  +--ro transceiver-tunability?   frequency-ghz
          |  +--ro tx-channel-power-min?       power-dbm
          |  +--ro tx-channel-power-max?       power-dbm
          |  +--ro rx-channel-power-min?       power-dbm
          |  +--ro rx-channel-power-max?       power-dbm
          |  +--ro rx-total-power-max?         power-dbm
          +--:(organizational-mode)
          |  +--ro organizational-mode
          |     +--ro operational-mode?           operational-mode
          |     +--ro organization-identifier?
          |     |       organization-identifier
          |     +--ro line-coding-bitrate*        identityref
          |     +--ro transmitter-tuning-range
          |     |  +--ro min-central-frequency?    frequency-thz
          |     |  +--ro max-central-frequency?    frequency-thz
          |     |  +--ro transceiver-tunability?   frequency-ghz
          |     +--ro tx-channel-power-min?       power-dbm
          |     +--ro tx-channel-power-max?       power-dbm
          |     +--ro rx-channel-power-min?       power-dbm
          |     +--ro rx-channel-power-max?       power-dbm
          |     +--ro rx-total-power-max?         power-dbm
          +--:(explicit-mode)
             +--ro explicit-mode
                +--ro transmitter-tuning-range
                |  +--ro min-central-frequency?    frequency-thz
                |  +--ro max-central-frequency?    frequency-thz
                |  +--ro transceiver-tunability?   frequency-ghz
                +--ro tx-channel-power-min?       power-dbm
                +--ro tx-channel-power-max?       power-dbm
                +--ro rx-channel-power-min?       power-dbm
                +--ro rx-channel-power-max?       power-dbm
                +--ro rx-total-power-max?         power-dbm
                +--ro compatible-modes
     grouping transceiver-capabilities:
       +--ro supported-modes!
          +--ro supported-mode* [mode-id]



Belotti, et al.            Expires 7 June 2025                 [Page 66]

Internet-Draft            L0 Common YANG Types             December 2024


             +--ro mode-id?                          string
             +--ro (mode)
                +--:(G.698.2)
                |  +--ro standard-mode?              standard-mode
                |  +--ro line-coding-bitrate*        identityref
                |  +--ro transmitter-tuning-range
                |  |  +--ro min-central-frequency?    frequency-thz
                |  |  +--ro max-central-frequency?    frequency-thz
                |  |  +--ro transceiver-tunability?   frequency-ghz
                |  +--ro tx-channel-power-min?       power-dbm
                |  +--ro tx-channel-power-max?       power-dbm
                |  +--ro rx-channel-power-min?       power-dbm
                |  +--ro rx-channel-power-max?       power-dbm
                |  +--ro rx-total-power-max?         power-dbm
                +--:(organizational-mode)
                |  +--ro organizational-mode
                |     +--ro operational-mode?           operational-mode
                |     +--ro organization-identifier?
                |     |       organization-identifier
                |     +--ro line-coding-bitrate*        identityref
                |     +--ro transmitter-tuning-range
                |     |  +--ro min-central-frequency?    frequency-thz
                |     |  +--ro max-central-frequency?    frequency-thz
                |     |  +--ro transceiver-tunability?   frequency-ghz
                |     +--ro tx-channel-power-min?       power-dbm
                |     +--ro tx-channel-power-max?       power-dbm
                |     +--ro rx-channel-power-min?       power-dbm
                |     +--ro rx-channel-power-max?       power-dbm
                |     +--ro rx-total-power-max?         power-dbm
                +--:(explicit-mode)
                   +--ro explicit-mode
                      +--ro transmitter-tuning-range
                      |  +--ro min-central-frequency?    frequency-thz
                      |  +--ro max-central-frequency?    frequency-thz
                      |  +--ro transceiver-tunability?   frequency-ghz
                      +--ro tx-channel-power-min?       power-dbm
                      +--ro tx-channel-power-max?       power-dbm
                      +--ro rx-channel-power-min?       power-dbm
                      +--ro rx-channel-power-max?       power-dbm
                      +--ro rx-total-power-max?         power-dbm
                      +--ro compatible-modes
                         +--ro supported-application-codes*
                         |       -> ../../../../supported-mode/mode-id
                         +--ro supported-organizational-modes*
                                 -> ../../../../supported-mode/mode-id
     grouping standard-mode:
       +--ro standard-mode?   standard-mode
     grouping organizational-mode:



Belotti, et al.            Expires 7 June 2025                 [Page 67]

Internet-Draft            L0 Common YANG Types             December 2024


       +--ro operational-mode?          operational-mode
       +--ro organization-identifier?   organization-identifier
     grouping penalty-value:
       +--ro penalty-value    union
     grouping explicit-mode:
       +--ro line-coding-bitrate?                identityref
       +--ro bitrate?                            uint16
       +--ro max-diff-group-delay?               decimal-2
       +--ro max-chromatic-dispersion?           decimal-2
       +--ro cd-penalty* [cd-value]
       |  +--ro cd-value         decimal-2
       |  +--ro penalty-value    union
       +--ro max-polarization-mode-dispersion?   decimal-2
       +--ro pmd-penalty* [pmd-value]
       |  +--ro pmd-value        decimal-2
       |  +--ro penalty-value    union
       +--ro max-polarization-dependent-loss     power-loss-or-null
       +--ro pdl-penalty* [pdl-value]
       |  +--ro pdl-value        power-loss
       |  +--ro penalty-value    union
       +--ro available-modulation-type?          identityref
       +--ro min-OSNR?                           snr
       +--ro rx-ref-channel-power?               power-dbm
       +--ro rx-channel-power-penalty* [rx-channel-power-value]
       |  +--ro rx-channel-power-value    power-dbm
       |  +--ro penalty-value             union
       +--ro min-Q-factor?                       decimal-2
       +--ro available-baud-rate?                decimal64
       +--ro roll-off?                           decimal64
       +--ro min-carrier-spacing?                frequency-ghz
       +--ro available-fec-type?                 identityref
       +--ro fec-code-rate?                      decimal64
       +--ro fec-threshold?                      decimal64
       +--ro in-band-osnr?                       snr
       +--ro out-of-band-osnr?                   snr
       +--ro tx-polarization-power-difference?   power-ratio
       +--ro polarization-skew?                  decimal-2
     grouping common-standard-organizational-mode:
       +--ro line-coding-bitrate*   identityref
     grouping transmitter-tuning-range:
       +-- min-central-frequency?    frequency-thz
       +-- max-central-frequency?    frequency-thz
       +-- transceiver-tunability?   frequency-ghz
     grouping common-all-modes:
       +--ro transmitter-tuning-range
       |  +--ro min-central-frequency?    frequency-thz
       |  +--ro max-central-frequency?    frequency-thz
       |  +--ro transceiver-tunability?   frequency-ghz



Belotti, et al.            Expires 7 June 2025                 [Page 68]

Internet-Draft            L0 Common YANG Types             December 2024


       +--ro tx-channel-power-min?       power-dbm
       +--ro tx-channel-power-max?       power-dbm
       +--ro rx-channel-power-min?       power-dbm
       +--ro rx-channel-power-max?       power-dbm
       +--ro rx-total-power-max?         power-dbm
     grouping common-transceiver-param:
       +-- line-coding-bitrate?   identityref
       +-- tx-channel-power?      power-dbm-or-null
       +--ro rx-channel-power?      power-dbm-or-null
       +--ro rx-total-power?        power-dbm-or-null
     grouping common-transceiver-configured-param:
       +-- line-coding-bitrate?   identityref
       +-- tx-channel-power?      power-dbm-or-null
     grouping common-transceiver-readonly-param:
       +--ro rx-channel-power?   power-dbm-or-null
       +--ro rx-total-power?     power-dbm-or-null
     grouping l0-tunnel-attributes:
       +-- wavelength-assignment?   identityref
     grouping frequency-range:
       +-- lower-frequency    frequency-thz
       +-- upper-frequency    frequency-thz
     grouping l0-path-constraints:
       +-- gsnr-extra-margin?   snr
     grouping l0-path-properties:
       +--ro estimated-gsnr?          snr
       +--ro estimated-eol-gsnr?      snr
       +--ro estimated-lowest-gsnr?   snr

                                  Figure 2

Appendix B.  Changes from RFC 9093

   This version adds new identities, data types, and groupings to the
   'ietf-layer0-types' YANG module.

   The following new YANG identities have been added to the 'ietf-
   layer0-types' module:

   *  cwdm-ch-spc-type

   *  flexi-ncfg-type

   *  flexi-ncfg-6p25gh

   *  modulation

   *  DPSK




Belotti, et al.            Expires 7 June 2025                 [Page 69]

Internet-Draft            L0 Common YANG Types             December 2024


   *  QPSK

   *  DP-QPSK

   *  QAM8

   *  DP-QAM8

   *  QAM16

   *  DP-QAM16

   *  QAM32

   *  DP-QAM32

   *  QAM64

   *  DP-QAM64

   *  fec-type

   *  g-fec

   *  super-fec

   *  no-fec

   *  sc-fec

   *  o-fec

   *  c-fec

   *  line-coding

   *  line-coding-NRZ-2p5G

   *  line-coding-NRZ-OTU1

   *  line-coding-NRZ-10G

   *  line-coding-NRZ-OTU2

   *  line-coding-OTL4.4-SC

   *  line-coding-FOIC1.4-SC




Belotti, et al.            Expires 7 June 2025                 [Page 70]

Internet-Draft            L0 Common YANG Types             December 2024


   *  wavelength-assignment

   *  first-fit-wavelength-assignment

   *  random-wavelength-assignment

   *  least-loaded-wavelength-assignment

   *  lower-first-wavelength-assignment

   *  upper-first-wavelength-assignment

   *  type-power-mode

   *  power-spectral-density

   *  carrier-power

   *  switching-wson-lsc

   *  switching-flexi-grid-lsc

   The following new YANG data types have been added to the 'ietf-
   layer0-types' module:

   *  Standard-mode

   *  Organization-identifier

   *  Operational-mode

   *  frequency-thz

   *  frequency-ghz

   *  snr

   *  snr-or-null

   *  fiber-type

   *  decimal-2

   *  decimal-2-or-null

   *  power-gain

   *  power-gain-or-null



Belotti, et al.            Expires 7 June 2025                 [Page 71]

Internet-Draft            L0 Common YANG Types             December 2024


   *  power-loss

   *  power-loss-or-null

   *  power-ratio

   *  power-ratio-or-null

   *  power-dbm

   *  power-dbm-or-null

   *  decimal-5

   *  decimal-5-or-null

   *  psd

   *  psd-or-null

   The following new YANG groupings have been added to the 'ietf-
   layer0-types' module:

   *  wdm-label-start-end

   *  wdm-label-step

   *  wdm-label-hop

   *  wdm-label-range-info

   *  transceiver-mode

   *  transceiver-capabilities

   *  standard-mode

   *  organizational-mode

   *  penalty-value

   *  explicit-mode

   *  common-standard-organizational-mode

   *  transmitter-tuning-range

   *  common-all-mode



Belotti, et al.            Expires 7 June 2025                 [Page 72]

Internet-Draft            L0 Common YANG Types             December 2024


   *  common-transceiver-param

   *  common-transceiver-configured-param

   *  common-transceiver-readonly-param

   *  l0-tunnel-attributes

   *  frequency-range

   *  l0-path-constraints

   *  l0-path-properties

Acknowledgments

   The authors and the working group give their sincere thanks to Robert
   Wilton for the YANG doctor review and to Adrian Farrel and Tom Petch
   for their comments during the model and document development.

   This document was prepared using kramdown.

Contributors

   Haomian Zheng
   Huawei
   Email: zhenghaomian@huawei.com


   Daniel King
   University of Lancaster
   Email: d.king@lancaster.ac.uk


   Gabriele Galimberti
   Cisco
   Email: ggalimbe@cisco.com


   Enrico Griseri
   Nokia
   Email: Enrico.Griseri@nokia.com


   Dhruv Dhody
   Huawei
   Email: dhruv.ietf@gmail.com




Belotti, et al.            Expires 7 June 2025                 [Page 73]

Internet-Draft            L0 Common YANG Types             December 2024


   Bin Yeong Yoon
   ETRI
   Email: byyun@etri.re.kr


   Ricard Vilalta
   CTTC
   Email: ricard.vilalta@cttc.es


   Young Lee
   Samsung
   Email: younglee.tx@gmail.com


   Victor Lopez
   Nokia
   Email: victor.lopez@nokia.com


Authors' Addresses

   Sergio Belotti (editor)
   Nokia
   Email: sergio.belotti@nokia.com


   Italo Busi (editor)
   Huawei
   Email: italo.busi@huawei.com


   Dieter Beller (editor)
   Nokia
   Email: dieter.beller@nokia.com


   Esther Le Rouzic
   Orange
   Email: esther.lerouzic@orange.com


   Aihua Guo
   Futurewei Technologies
   Email: aihuaguo.ietf@gmail.com






Belotti, et al.            Expires 7 June 2025                 [Page 74]