patch-2.3.10 linux/drivers/char/cyclades.c
Next file: linux/drivers/char/dn_keyb.c
Previous file: linux/drivers/char/consolemap.c
Back to the patch index
Back to the overall index
- Lines: 768
- Date:
Tue Jul 6 19:05:48 1999
- Orig file:
v2.3.9/linux/drivers/char/cyclades.c
- Orig date:
Mon May 24 22:38:07 1999
diff -u --recursive --new-file v2.3.9/linux/drivers/char/cyclades.c linux/drivers/char/cyclades.c
@@ -1,7 +1,7 @@
#define BLOCKMOVE
#define Z_WAKE
static char rcsid[] =
-"$Revision: 2.2.2.2 $$Date: 1999/05/21 17:18:15 $";
+"$Revision: 2.2.2.3 $$Date: 1999/06/28 11:13:29 $";
/*
* linux/drivers/char/cyclades.c
@@ -31,6 +31,16 @@
* void cleanup_module(void);
*
* $Log: cyclades.c,v $
+ * Revision 2.2.2.3 1999/06/28 11:13:29 ivan
+ * Added support for interrupt mode operation for the Z cards;
+ * Removed the driver inactivity control for the Z;
+ * Added a missing MOD_DEC_USE_COUNT in the cy_open function for when
+ * the Z firmware is not loaded yet;
+ * Replaced the "manual" Z Tx flush buffer by a call to a FW command of
+ * same functionality;
+ * Implemented workaround for IRQ setting loss on the PCI configuration
+ * registers after a PCI bridge EEPROM reload (affects PLX9060 only);
+ *
* Revision 2.2.2.2 1999/05/14 17:18:15 ivan
* /proc entry location changed to /proc/tty/driver/cyclades;
* Added support to shared IRQ's (only for PCI boards);
@@ -528,7 +538,7 @@
constant in the definition below. No other change is necessary to
support more boards/ports. */
-#define NR_PORTS 128
+#define NR_PORTS 256
#define ZE_V1_NPORTS 64
#define ZO_V1 0
@@ -810,13 +820,15 @@
#ifndef CONFIG_COBALT_27
static void cy_probe(int, void *, struct pt_regs *);
#endif /* CONFIG_COBALT_27 */
-static void cyz_poll(unsigned long);
#ifdef CYCLOM_SHOW_STATUS
static void show_status(int);
#endif
static int cyclades_get_proc_info(char *, char **, off_t , int , int *, void *);
+#ifndef CONFIG_CYZ_INTR
+static void cyz_poll(unsigned long);
+
/* The Cyclades-Z polling cycle is defined by this variable */
static long cyz_polling_cycle = CZ_DEF_POLL;
@@ -825,6 +837,7 @@
cyz_timerlist = {
NULL, NULL, 0, 0, cyz_poll
};
+#endif /* CONFIG_CYZ_INTR */
/**************************************************
error = verify_area(VERIFY_WRITE, (void *) arg, sizeof(unsigned long));
@@ -1197,7 +1210,7 @@
if((cinfo = (struct cyclades_card *)dev_id) == 0){
#ifdef CY_DEBUG_INTERRUPTS
- printk("cy_interrupt: spurious interrupt %d\n\r", irq);
+ printk("cyy_interrupt: spurious interrupt %d\n\r", irq);
#endif
return; /* spurious interrupt */
}
@@ -1229,7 +1242,7 @@
}
if (status & CySRReceive) { /* reception interrupt */
#ifdef CY_DEBUG_INTERRUPTS
- printk("cy_interrupt: rcvd intr, chip %d\n\r", chip);
+ printk("cyy_interrupt: rcvd intr, chip %d\n\r", chip);
#endif
/* determine the channel & change to that context */
save_xir = (u_char) cy_readb(base_addr+(CyRIR<<index));
@@ -1356,7 +1369,7 @@
is empty, we know we can always stuff a dozen
characters. */
#ifdef CY_DEBUG_INTERRUPTS
- printk("cy_interrupt: xmit intr, chip %d\n\r", chip);
+ printk("cyy_interrupt: xmit intr, chip %d\n\r", chip);
#endif
/* determine the channel & change to that context */
@@ -1636,12 +1649,285 @@
} /* cyz_update_channel */
#endif
-
+#ifdef CONFIG_CYZ_INTR
static void
cyz_interrupt(int irq, void *dev_id, struct pt_regs *regs)
{
+ struct tty_struct *tty;
+ struct cyclades_card *cinfo;
+ struct cyclades_port *info;
+ static volatile struct FIRM_ID *firm_id;
+ static volatile struct ZFW_CTRL *zfw_ctrl;
+ static volatile struct BOARD_CTRL *board_ctrl;
+ static volatile struct CH_CTRL *ch_ctrl;
+ static volatile struct BUF_CTRL *buf_ctrl;
+ uclong channel;
+ ucchar cmd;
+ uclong param;
+ uclong hw_ver, fw_ver;
+ char data;
+ volatile int char_count, special_count;
+#ifdef BLOCKMOVE
+ int small_count;
+#endif
+ volatile uclong tx_put, tx_get, tx_bufsize;
+ volatile uclong rx_put, rx_get, rx_bufsize;
+
+ if((cinfo = (struct cyclades_card *)dev_id) == 0){
+#ifdef CY_DEBUG_INTERRUPTS
+ printk("cyz_interrupt: spurious interrupt %d\n\r", irq);
+#endif
+ return; /* spurious interrupt */
+ }
+
+ firm_id = (struct FIRM_ID *)(cinfo->base_addr + ID_ADDRESS);
+ if (!ISZLOADED(*cinfo)) {
+#ifdef CY_DEBUG_INTERRUPTS
+ printk("cyz_interrupt: board not yet loaded (INT %d).\n\r", irq);
+#endif
+ return;
+ }
+
+ zfw_ctrl = (struct ZFW_CTRL *)
+ (cinfo->base_addr + cy_readl(&firm_id->zfwctrl_addr));
+ board_ctrl = &(zfw_ctrl->board_ctrl);
+ fw_ver = cy_readl(&board_ctrl->fw_version);
+ hw_ver = cy_readl(&((struct RUNTIME_9060 *)
+ (cinfo->ctl_addr))->mail_box_0);
+
+ while(cyz_fetch_msg(cinfo, &channel, &cmd, ¶m) == 1) {
+ special_count = 0;
+ info = &cy_port[channel + cinfo->first_line];
+ if((tty = info->tty) == 0) continue;
+ ch_ctrl = &(zfw_ctrl->ch_ctrl[channel]);
+ buf_ctrl = &(zfw_ctrl->buf_ctrl[channel]);
+
+ switch(cmd){
+ case C_CM_PR_ERROR:
+ tty->flip.count++;
+ *tty->flip.flag_buf_ptr++ = TTY_PARITY;
+ *tty->flip.char_buf_ptr++ = 0;
+ special_count++;
+ break;
+ case C_CM_FR_ERROR:
+ tty->flip.count++;
+ *tty->flip.flag_buf_ptr++ = TTY_FRAME;
+ *tty->flip.char_buf_ptr++ = 0;
+ special_count++;
+ break;
+ case C_CM_RXBRK:
+ tty->flip.count++;
+ *tty->flip.flag_buf_ptr++ = TTY_BREAK;
+ *tty->flip.char_buf_ptr++ = 0;
+ special_count++;
+ break;
+ case C_CM_MDCD:
+ if (info->flags & ASYNC_CHECK_CD){
+ if ((fw_ver > 241 ?
+ ((u_long)param) :
+ cy_readl(&ch_ctrl[channel].rs_status)) & C_RS_DCD) {
+ /* SP("Open Wakeup\n"); */
+ cy_sched_event(info,
+ Cy_EVENT_OPEN_WAKEUP);
+ }else if(!((info->flags
+ & ASYNC_CALLOUT_ACTIVE)
+ &&(info->flags
+ & ASYNC_CALLOUT_NOHUP))){
+ /* SP("Hangup\n"); */
+ cy_sched_event(info,
+ Cy_EVENT_HANGUP);
+ }
+ }
+ break;
+ case C_CM_MCTS:
+ if (info->flags & ASYNC_CTS_FLOW) {
+ if(info->tty->hw_stopped){
+ if( cy_readl(&ch_ctrl[channel].rs_status) & C_RS_DCD){
+ /* cy_start isn't used because...
+ HW flow is handled by the board */
+ /* SP("Write Wakeup\n"); */
+ cy_sched_event(info,
+ Cy_EVENT_WRITE_WAKEUP);
+ }
+ }else{
+ if(!(cy_readl(&ch_ctrl[channel].rs_status) & C_RS_CTS)){
+ /* cy_stop isn't used because
+ HW flow is handled by the board */
+ /* SP("Write stop\n"); */
+ }
+ }
+ }
+ break;
+ case C_CM_MRI:
+ break;
+ case C_CM_MDSR:
+ break;
+#ifdef Z_WAKE
+ case C_CM_IOCTLW:
+ cy_sched_event(info, Cy_EVENT_SHUTDOWN_WAKEUP);
+ break;
+#endif
+ case C_CM_RXHIWM:
+ case C_CM_RXNNDT:
+ /* Reception Interrupt */
+#ifdef CY_DEBUG_INTERRUPTS
+ printk("cyz_interrupt: rcvd intr, card %d, port %ld\n\r",
+ info->card, channel);
+#endif
+
+ rx_get = cy_readl(&buf_ctrl->rx_get);
+ rx_put = cy_readl(&buf_ctrl->rx_put);
+ rx_bufsize = cy_readl(&buf_ctrl->rx_bufsize);
+ if (rx_put >= rx_get)
+ char_count = rx_put - rx_get;
+ else
+ char_count = rx_put - rx_get + rx_bufsize;
+
+ if ( char_count ){
+
+#ifdef CY_ENABLE_MONITORING
+ info->mon.int_count++;
+ info->mon.char_count += char_count;
+ if (char_count > info->mon.char_max)
+ info->mon.char_max = char_count;
+ info->mon.char_last = char_count;
+#endif
+ info->idle_stats.recv_bytes += char_count;
+ info->idle_stats.recv_idle = jiffies;
+ if( tty == 0){
+ /* flush received characters */
+ rx_get = (rx_get + char_count) & (rx_bufsize - 1);
+ /* SP("-"); */
+ info->rflush_count++;
+ }else{
+#ifdef BLOCKMOVE
+ /* we'd like to use memcpy(t, f, n) and memset(s, c, count)
+ for performance, but because of buffer boundaries, there
+ may be several steps to the operation */
+ while(0 < (small_count
+ = cy_min((rx_bufsize - rx_get),
+ cy_min((TTY_FLIPBUF_SIZE - tty->flip.count),
+ char_count)))){
+
+ memcpy_fromio(tty->flip.char_buf_ptr,
+ (char *)(cinfo->base_addr
+ + cy_readl(&buf_ctrl->rx_bufaddr)
+ + rx_get),
+ small_count);
+
+ tty->flip.char_buf_ptr += small_count;
+ memset(tty->flip.flag_buf_ptr,
+ TTY_NORMAL,
+ small_count);
+ tty->flip.flag_buf_ptr += small_count;
+ rx_get = (rx_get + small_count) & (rx_bufsize - 1);
+ char_count -= small_count;
+ tty->flip.count += small_count;
+ }
+#else
+ while(char_count--){
+ if (tty->flip.count >= TTY_FLIPBUF_SIZE){
+ break;
+ }
+ data = cy_readb(cinfo->base_addr +
+ cy_readl(&buf_ctrl->rx_bufaddr) + rx_get);
+ rx_get = (rx_get + 1) & (rx_bufsize - 1);
+ tty->flip.count++;
+ *tty->flip.flag_buf_ptr++ = TTY_NORMAL;
+ *tty->flip.char_buf_ptr++ = data;
+ }
+#endif
+ queue_task(&tty->flip.tqueue, &tq_timer);
+ }
+ /* Update rx_get */
+ cy_writel(&buf_ctrl->rx_get, rx_get);
+ }
+ break;
+ case C_CM_TXBEMPTY:
+ case C_CM_TXLOWWM:
+ case C_CM_INTBACK:
+ /* Transmission Interrupt */
+#ifdef CY_DEBUG_INTERRUPTS
+ printk("cyz_interrupt: xmit intr, card %d, port %ld\n\r",
+ info->card, channel);
+#endif
+
+ tx_get = cy_readl(&buf_ctrl->tx_get);
+ tx_put = cy_readl(&buf_ctrl->tx_put);
+ tx_bufsize = cy_readl(&buf_ctrl->tx_bufsize);
+ if (tx_put >= tx_get)
+ char_count = tx_get - tx_put - 1 + tx_bufsize;
+ else
+ char_count = tx_get - tx_put - 1;
+
+ if ( char_count ){
+
+ if( tty == 0 ){
+ goto ztxdone;
+ }
+
+ if(info->x_char) { /* send special char */
+ data = info->x_char;
+
+ cy_writeb((cinfo->base_addr +
+ cy_readl(&buf_ctrl->tx_bufaddr) + tx_put), data);
+ tx_put = (tx_put + 1) & (tx_bufsize - 1);
+ info->x_char = 0;
+ char_count--;
+ }
+#ifdef BLOCKMOVE
+ while(0 < (small_count
+ = cy_min((tx_bufsize - tx_put),
+ cy_min ((SERIAL_XMIT_SIZE - info->xmit_tail),
+ cy_min(info->xmit_cnt, char_count))))){
+
+ memcpy_toio((char *)(cinfo->base_addr
+ + cy_readl(&buf_ctrl->tx_bufaddr) + tx_put),
+ &info->xmit_buf[info->xmit_tail],
+ small_count);
+
+ tx_put = (tx_put + small_count) & (tx_bufsize - 1);
+ char_count -= small_count;
+ info->xmit_cnt -= small_count;
+ info->xmit_tail =
+ (info->xmit_tail + small_count) & (SERIAL_XMIT_SIZE - 1);
+ }
+#else
+ while (info->xmit_cnt && char_count){
+ data = info->xmit_buf[info->xmit_tail];
+ info->xmit_cnt--;
+ info->xmit_tail =
+ (info->xmit_tail + 1) & (SERIAL_XMIT_SIZE - 1);
+
+ cy_writeb(cinfo->base_addr +
+ cy_readl(&buf_ctrl->tx_bufaddr) + tx_put,
+ data);
+ tx_put = (tx_put + 1) & (tx_bufsize - 1);
+ char_count--;
+ }
+
+#endif
+ ztxdone:
+ if (info->xmit_cnt < WAKEUP_CHARS) {
+ cy_sched_event(info, Cy_EVENT_WRITE_WAKEUP);
+ }
+ /* Update tx_put */
+ cy_writel(&buf_ctrl->tx_put, tx_put);
+ }
+ break;
+ case C_CM_FATAL:
+ /* should do something with this !!! */
+ break;
+ }
+ if(special_count){
+ queue_task(&tty->flip.tqueue, &tq_timer);
+ }
+ }
+
+ return;
} /* cyz_interrupt */
+#else /* CONFIG_CYZ_INTR */
static void
cyz_poll(unsigned long arg)
@@ -1675,7 +1961,6 @@
firm_id = (struct FIRM_ID *)(cinfo->base_addr + ID_ADDRESS);
if (!ISZLOADED(*cinfo)) {
- cinfo->inact_ctrl = 0;
continue;
}
@@ -1686,12 +1971,6 @@
hw_ver = cy_readl(&((struct RUNTIME_9060 *)
(cinfo->ctl_addr))->mail_box_0);
- /* Enables the firmware inactivity control */
- if ((fw_ver > 0x00000310L) && (!cinfo->inact_ctrl)) {
- param = cyz_issue_cmd( &cy_card[card], 0L, C_CM_TINACT, 0L);
- cinfo->inact_ctrl = 1;
- }
-
while(cyz_fetch_msg(cinfo, &channel, &cmd, ¶m) == 1){
char_count = 0;
info = &cy_port[ channel + cinfo->first_line ];
@@ -1922,17 +2201,13 @@
}
/* poll every 40 ms */
cyz_timerlist.expires = jiffies + cyz_polling_cycle;
-
- /* refresh inactivity counter */
- if (cinfo->inact_ctrl) {
- cy_writel(&board_ctrl->inactivity, (uclong) ZF_TINACT);
- }
}
add_timer(&cyz_timerlist);
return;
} /* cyz_poll */
+#endif /* CONFIG_CYZ_INTR */
/********** End of block of Cyclades-Z specific code *********/
/***********************************************************/
@@ -2053,12 +2328,27 @@
cy_writel(&ch_ctrl[channel].op_mode, C_CH_ENABLE);
#ifdef Z_WAKE
+#ifdef CONFIG_CYZ_INTR
cy_writel(&ch_ctrl[channel].intr_enable,
- C_IN_MDCD|C_IN_MCTS|C_IN_IOCTLW);
+ C_IN_TXBEMPTY|C_IN_TXLOWWM|C_IN_RXHIWM|C_IN_RXNNDT|
+ C_IN_IOCTLW|
+ C_IN_MDCD|C_IN_MCTS);
#else
cy_writel(&ch_ctrl[channel].intr_enable,
+ C_IN_IOCTLW|
C_IN_MDCD|C_IN_MCTS);
-#endif
+#endif /* CONFIG_CYZ_INTR */
+#else
+#ifdef CONFIG_CYZ_INTR
+ cy_writel(&ch_ctrl[channel].intr_enable,
+ C_IN_TXBEMPTY|C_IN_TXLOWWM|C_IN_RXHIWM|C_IN_RXNNDT|
+ C_IN_MDCD|C_IN_MCTS);
+#else
+ cy_writel(&ch_ctrl[channel].intr_enable,
+ C_IN_MDCD|C_IN_MCTS);
+#endif /* CONFIG_CYZ_INTR */
+#endif /* Z_WAKE */
+
retval = cyz_issue_cmd( &cy_card[card],
channel, C_CM_IOCTL, 0L); /* was C_CM_RESET */
if (retval != 0){
@@ -2126,11 +2416,21 @@
cy_readb(base_addr+(CySRER<<index)) | CyTxMpty);
restore_flags(flags);
} else {
+#ifdef CONFIG_CYZ_INTR
+ int retval;
+
+ save_flags(flags); cli();
+ retval = cyz_issue_cmd(&cy_card[card], channel, C_CM_INTBACK, 0L);
+ if (retval != 0){
+ printk("cyc:start_xmit retval was %x\n", retval);
+ }
+ restore_flags(flags);
+#else /* CONFIG_CYZ_INTR */
/* Don't have to do anything at this time */
+#endif /* CONFIG_CYZ_INTR */
}
} /* start_xmit */
-
/*
* This routine shuts down a serial port; interrupts are disabled,
* and DTR is dropped if the hangup on close termio flag is on.
@@ -2504,8 +2804,24 @@
} else {
printk("cyc:Cyclades-Z firmware not yet loaded\n");
}
+ MOD_DEC_USE_COUNT;
return -ENODEV;
}
+#ifdef CONFIG_CYZ_INTR
+ else {
+ /* In case this Z board is operating in interrupt mode, its
+ interrupts should be enabled as soon as the first open happens
+ to one of its ports. */
+ if (!cy_card[info->card].intr_enabled) {
+ retval = cyz_issue_cmd(&cy_card[info->card],
+ 0, C_CM_IRQ_ENBL, 0L);
+ if (retval != 0){
+ printk("cyc:IRQ enable retval was %x\n", retval);
+ }
+ cy_card[info->card].intr_enabled = 1;
+ }
+ }
+#endif /* CONFIG_CYZ_INTR */
}
#ifdef CY_DEBUG_OTHER
printk("cyc:cy_open ttyC%d\n", info->line); /* */
@@ -2640,7 +2956,6 @@
printk("Not clean (jiff=%lu)...", jiffies);
#endif
current->state = TASK_INTERRUPTIBLE;
- current->counter = 0; /* make us low-priority */
schedule_timeout(char_time);
if (signal_pending(current))
break;
@@ -2653,7 +2968,6 @@
}
/* Run one more char cycle */
current->state = TASK_INTERRUPTIBLE;
- current->counter = 0; /* make us low-priority */
schedule_timeout(char_time * 5);
current->state = TASK_RUNNING;
#ifdef CY_DEBUG_WAIT_UNTIL_SENT
@@ -3798,14 +4112,14 @@
if (break_state == -1) {
if (!info->breakon) {
info->breakon = 1;
- if (!info->xmit_cnt ) {
+ if (!info->xmit_cnt) {
start_xmit(info);
}
}
} else {
if (!info->breakoff) {
info->breakoff = 1;
- if (!info->xmit_cnt ) {
+ if (!info->xmit_cnt) {
start_xmit(info);
}
}
@@ -4053,6 +4367,7 @@
case CYGETCD1400VER:
ret_val = info->chip_rev;
break;
+#ifndef CONFIG_CYZ_INTR
case CYZSETPOLLCYCLE:
cyz_polling_cycle = (arg * HZ) / 1000;
ret_val = 0;
@@ -4060,6 +4375,7 @@
case CYZGETPOLLCYCLE:
ret_val = (cyz_polling_cycle * 1000) / HZ;
break;
+#endif /* CONFIG_CYZ_INTR */
case CYSETWAIT:
info->closing_wait = (unsigned short)arg * HZ/100;
ret_val = 0;
@@ -4333,7 +4649,7 @@
cy_flush_buffer(struct tty_struct *tty)
{
struct cyclades_port *info = (struct cyclades_port *)tty->driver_data;
- int card, channel;
+ int card, channel, retval;
unsigned long flags;
#ifdef CY_DEBUG_IO
@@ -4351,19 +4667,10 @@
if (IS_CYC_Z(cy_card[card])) { /* If it is a Z card, flush the on-board
buffers as well */
- static volatile struct FIRM_ID *firm_id;
- static volatile struct ZFW_CTRL *zfw_ctrl;
- static volatile struct CH_CTRL *ch_ctrl;
- static volatile struct BUF_CTRL *buf_ctrl;
-
- firm_id = (struct FIRM_ID *)(cy_card[card].base_addr + ID_ADDRESS);
- zfw_ctrl = (struct ZFW_CTRL *) (cy_card[card].base_addr +
- cy_readl(&firm_id->zfwctrl_addr));
- ch_ctrl = &(zfw_ctrl->ch_ctrl[channel]);
- buf_ctrl = &(zfw_ctrl->buf_ctrl[channel]);
-
- while (cy_readl(&buf_ctrl->tx_get) != cy_readl(&buf_ctrl->tx_put))
- cy_writel(&buf_ctrl->tx_put, cy_readl(&buf_ctrl->tx_get));
+ retval = cyz_issue_cmd(&cy_card[card], channel, C_CM_FLUSH_TX, 0L);
+ if (retval != 0) {
+ printk("cyc: flush_buffer retval was %x\n", retval);
+ }
}
wake_up_interruptible(&tty->write_wait);
if ((tty->flags & (1 << TTY_DO_WRITE_WAKEUP))
@@ -4410,8 +4717,8 @@
/* initialize chips on Cyclom-Y card -- return number of valid
chips (which is number of ports/4) */
-__initfunc(static unsigned short
-cyy_init_card(volatile ucchar *true_base_addr,int index))
+static unsigned short __init
+cyy_init_card(volatile ucchar *true_base_addr,int index)
{
unsigned int chip_number;
volatile ucchar* base_addr;
@@ -4496,8 +4803,7 @@
* sets global variables and return the number of ISA boards found.
* ---------------------------------------------------------------------
*/
-__initfunc(static int
-cy_detect_isa(void))
+static int __init cy_detect_isa(void)
{
unsigned short cy_isa_irq,nboard;
volatile ucchar *cy_isa_address;
@@ -4604,8 +4910,8 @@
* sets global variables and return the number of PCI boards found.
* ---------------------------------------------------------------------
*/
-__initfunc(static int
-cy_detect_pci(void))
+static int __init
+cy_detect_pci(void)
{
#ifdef CONFIG_PCI
@@ -4872,10 +5178,11 @@
return(i);
}
+#ifdef CONFIG_CYZ_INTR
/* allocate IRQ only if board has an IRQ */
- if( (1 < cy_pci_irq) && (cy_pci_irq < 15) ) {
- if(request_irq(cy_pci_irq,cyz_interrupt,
- SA_SHIRQ,"Cyclades-Z",&cy_card[j]))
+ if( (cy_pci_irq != 0) && (cy_pci_irq != 255) ) {
+ if(request_irq(cy_pci_irq, cyz_interrupt,
+ SA_SHIRQ, "Cyclades-Z", &cy_card[j]))
{
printk("Could not allocate IRQ%d ",
cy_pci_irq);
@@ -4884,6 +5191,7 @@
return(i);
}
}
+#endif /* CONFIG_CYZ_INTR */
/* set cy_card */
@@ -4896,7 +5204,7 @@
/* print message */
/* don't report IRQ if board is no IRQ */
- if( (cy_pci_irq < 15) && (cy_pci_irq > 1) ) {
+ if( (cy_pci_irq != 0) && (cy_pci_irq != 255) ) {
printk("Cyclades-8Zo/PCI #%d: 0x%lx-0x%lx, IRQ%d, ",
j+1,(ulong)cy_pci_addr2,
(ulong)(cy_pci_addr2 + CyPCI_Zwin - 1),
@@ -4908,6 +5216,11 @@
}
printk("%d channels starting from port %d.\n",
cy_pci_nchan,cy_next_channel);
+#ifdef CONFIG_CYZ_INTR
+ /* Enable interrupts on the PLX chip */
+ cy_writew(cy_pci_addr0+0x68,
+ cy_readw(cy_pci_addr0+0x68)|0x0900);
+#endif /* CONFIG_CYZ_INTR */
cy_next_channel += cy_pci_nchan;
}
}
@@ -4927,10 +5240,6 @@
(ulong)cy_pci_addr2, (ulong)cy_pci_addr0);
printk("Cyclades-Z/PCI: New Cyclades-Z board. FPGA not loaded\n");
#endif
- /* The following clears the firmware id word. This ensures
- that the driver will not attempt to talk to the board
- until it has been properly initialized.
- */
PAUSE
/* This must be the new Cyclades-Ze/PCI. */
cy_pci_nchan = ZE_V1_NPORTS;
@@ -4955,10 +5264,11 @@
return(i);
}
+#ifdef CONFIG_CYZ_INTR
/* allocate IRQ only if board has an IRQ */
- if( (1 < cy_pci_irq) && (cy_pci_irq < 15) ) {
- if(request_irq(cy_pci_irq,cyz_interrupt,
- SA_SHIRQ,"Cyclades-Z",&cy_card[j]))
+ if( (cy_pci_irq != 0) && (cy_pci_irq != 255) ) {
+ if(request_irq(cy_pci_irq, cyz_interrupt,
+ SA_SHIRQ, "Cyclades-Z", &cy_card[j]))
{
printk("Could not allocate IRQ%d ",
cy_pci_irq);
@@ -4967,6 +5277,7 @@
return(i);
}
}
+#endif /* CONFIG_CYZ_INTR */
/* set cy_card */
cy_card[j].base_addr = cy_pci_addr2;
@@ -4978,7 +5289,7 @@
/* print message */
/* don't report IRQ if board is no IRQ */
- if( (cy_pci_irq < 15) && (cy_pci_irq > 1) ) {
+ if( (cy_pci_irq != 0) && (cy_pci_irq != 255) ) {
printk("Cyclades-Ze/PCI #%d: 0x%lx-0x%lx, IRQ%d, ",
j+1,(ulong)cy_pci_addr2,
(ulong)(cy_pci_addr2 + CyPCI_Ze_win - 1),
@@ -4990,6 +5301,11 @@
}
printk("%d channels starting from port %d.\n",
cy_pci_nchan,cy_next_channel);
+#ifdef CONFIG_CYZ_INTR
+ /* Enable interrupts on the PLX chip */
+ cy_writew(cy_pci_addr0+0x68,
+ cy_readw(cy_pci_addr0+0x68)|0x0900);
+#endif /* CONFIG_CYZ_INTR */
cy_next_channel += cy_pci_nchan;
}
if (ZeIndex != 0) {
@@ -5098,8 +5414,8 @@
extra ports are ignored.
*/
-__initfunc(int
-cy_init(void))
+int __init
+cy_init(void)
{
struct cyclades_port *info;
struct cyclades_card *cinfo;
@@ -5219,6 +5535,7 @@
mailbox = cy_readl(&((struct RUNTIME_9060 *)
cy_card[board].ctl_addr)->mail_box_0);
nports = (mailbox == ZE_V1) ? ZE_V1_NPORTS : 8;
+ cinfo->intr_enabled = 0;
for (port = cinfo->first_line ;
port < cinfo->first_line + nports;
port++)
@@ -5342,15 +5659,17 @@
}
}
}
-
- if ( number_z_boards && !cyz_timeron){
- cyz_timeron++;
+
+#ifndef CONFIG_CYZ_INTR
+ if (number_z_boards && !cyz_timeron){
+ cyz_timeron++;
cyz_timerlist.expires = jiffies + 1;
add_timer(&cyz_timerlist);
#ifdef CY_PCI_DEBUG
printk("Cyclades-Z polling initialized\n");
#endif
}
+#endif /* CONFIG_CYZ_INTR */
#ifdef CY_PROC
ent = create_proc_entry("cyclades", S_IFREG | S_IRUGO, 0);
@@ -5377,10 +5696,12 @@
int e1, e2;
unsigned long flags;
+#ifndef CONFIG_CYZ_INTR
if (cyz_timeron){
cyz_timeron = 0;
del_timer(&cyz_timerlist);
}
+#endif /* CONFIG_CYZ_INTR */
save_flags(flags); cli();
remove_bh(CYCLADES_BH);
@@ -5396,6 +5717,9 @@
for (i = 0; i < NR_CARDS; i++) {
if (cy_card[i].base_addr != 0
+#ifndef CONFIG_CYZ_INTR
+ && cy_card[i].num_chips != -1 /* not a Z card */
+#endif /* CONFIG_CYZ_INTR */
&& cy_card[i].irq)
{
free_irq(cy_card[i].irq, &cy_card[i]);
FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen (who was at: slshen@lbl.gov)