A Semantic Definition Format for Data and Interactions of ThingsR. Mohan Internet-Draft B. Brinckman Intended status: Standards Track Cisco Systems Expires: 24 July 2026 L. Corneo Ericsson 20 January 2026 Protocol Mapping for SDF draft-ietf-asdf-sdf-protocol-mapping-03 Abstract This document defines protocol mapping extensions for the Semantic Definition Format (SDF) to enable mapping of protocol-agnostic SDF affordances to protocol-specific operations. The protocol mapping mechanism allows SDF models to specify how properties, actions, and events should be accessed using specific non-IP and IP protocols such as Bluetooth Low Energy, Zigbee or HTTP and CoAP. About This Document This note is to be removed before publishing as an RFC. Status information for this document may be found at https://datatracker.ietf.org/doc/draft-ietf-asdf-sdf-protocol- mapping/. Discussion of this document takes place on the A Semantic Definition Format for Data and Interactions of Things Working Group mailing list (mailto:asdf@ietf.org), which is archived at https://mailarchive.ietf.org/arch/browse/asdf/. Subscribe at https://www.ietf.org/mailman/listinfo/asdf/. Source for this draft and an issue tracker can be found at https://github.com/ietf-wg-asdf/sdf-protocol-mapping. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at https://datatracker.ietf.org/drafts/current/. Mohan, et al. Expires 24 July 2026 [Page 1] Internet-Draft sdf-protocol-mapping January 2026 Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on 24 July 2026. Copyright Notice Copyright (c) 2026 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/ license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Revised BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Revised BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3 2. Conventions and Definitions . . . . . . . . . . . . . . . . . 3 3. Structure . . . . . . . . . . . . . . . . . . . . . . . . . . 3 4. Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5. Examples . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5.1. BLE Protocol Mapping . . . . . . . . . . . . . . . . . . 7 5.1.1. BLE Protocol Mapping Structure . . . . . . . . . . . 7 5.2. Zigbee Protocol Mapping . . . . . . . . . . . . . . . . . 10 5.2.1. Zigbee Protocol Mapping Structure . . . . . . . . . . 10 6. SCIM SDF Extension . . . . . . . . . . . . . . . . . . . . . 12 7. Security Considerations . . . . . . . . . . . . . . . . . . . 14 8. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 14 8.1. Protocol Mapping . . . . . . . . . . . . . . . . . . . . 14 8.2. SCIM Device Schema SDF Extension . . . . . . . . . . . . 15 9. References . . . . . . . . . . . . . . . . . . . . . . . . . 15 9.1. Normative References . . . . . . . . . . . . . . . . . . 15 9.2. Informative References . . . . . . . . . . . . . . . . . 16 Appendix A. CDDL Definition . . . . . . . . . . . . . . . . . . 16 Appendix B. OpenAPI Definition . . . . . . . . . . . . . . . . . 18 B.1. Protocol map for BLE . . . . . . . . . . . . . . . . . . 19 B.2. Protocol map for Zigbee . . . . . . . . . . . . . . . . . 21 Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . . 22 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 22 Mohan, et al. Expires 24 July 2026 [Page 2] Internet-Draft sdf-protocol-mapping January 2026 1. Introduction The Semantic Definition Format (SDF) [I-D.ietf-asdf-sdf] provides a protocol-agnostic way to describe IoT devices and their capabilities through properties, actions, and events (collectively called affordances). However, when implementing these affordances on actual devices using specific communication protocols, there needs to be a mechanism to map the protocol-agnostic SDF definitions to protocol- specific operations. These protocols can be non-IP protocols that are commonly used in IoT environments, such as [BLE53] and [Zigbee22]. The protocol mapping mechanism is designed to be extensible, allowing future specifications to define mappings for IP-based protocols such as HTTP [RFC2616] or CoAP [RFC7252]. To leverage an SDF model to perform protocol-specific operations on an instance of a device, a mapping of the SDF affordance to a protocol-specific attribute is required. This document defines the protocol mapping mechanism using the sdfProtocolMap keyword, which allows SDF models to include protocol-specific mapping information alongside the protocol-agnostic definitions. 2. Conventions and Definitions The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here. 3. Structure Protocol mapping is required to map a protocol-agnostic affordance to a protocol-specific operation, as implementations of the same affordance will differ between protocols. For example, BLE will address a property as a service characteristic, while a property in Zigbee is addressed as an attribute in a cluster of an endpoint. A protocol mapping object is a JSON object identified by the sdfProtocolMap keyword. Protocol-specific properties are embedded within this object, organized by protocol name, e.g., "ble" or "zigbee". The protocol name MUST be specified in the IANA registry requested in Section 8.1. Mohan, et al. Expires 24 July 2026 [Page 3] Internet-Draft sdf-protocol-mapping January 2026 sdfProtocolMap | +-----> ble | | | +--> BLE-specific mapping | +-----> zigbee | +--> Zigbee-specific mapping Figure 1: Property Mapping As shown in Figure 1, protocol-specific properties must be embedded in an sdfProtocolMap object, for example a "ble" or a "zigbee" object. +===========+========+===========================================+ | Attribute | Type | Example | +===========+========+===========================================+ | ble | object | an object with BLE-specific attributes | +-----------+--------+-------------------------------------------+ | zigbee | object | an object with Zigbee-specific attributes | +-----------+--------+-------------------------------------------+ Table 1: Protocol objects where- * "ble" is an object containing properties that are specific to the BLE protocol. * "zigbee" is an object containing properties that are specific to the Zigbee protocol. * Other protocol mapping objects can be added by creating a new protocol object Example protocol mapping: Mohan, et al. Expires 24 July 2026 [Page 4] Internet-Draft sdf-protocol-mapping January 2026 { "sdfObject": { "healthsensor": { "sdfProperty": { "heartrate": { "description": "The current measured heart rate", "type": "number", "unit": "beat/min", "observable": false, "writable": false, "sdfProtocolMap": { "ble": { "serviceID": "12345678-1234-5678-1234-56789abcdef4", "characteristicID": "12345678-1234-5678-1234-56789abcdef4" } } } } } } } Figure 2: Example property mapping For properties that have a different protocol mapping for read and write operations, the protocol mapping can be specified as such: Mohan, et al. Expires 24 July 2026 [Page 5] Internet-Draft sdf-protocol-mapping January 2026 { "sdfObject": { "healthsensor": { "sdfProperty": { "heartrate": { "description": "The current measured heart rate", "type": "number", "unit": "beat/min", "observable": false, "sdfProtocolMap": { "ble": { "read": { "serviceID": "12345678-1234-5678-1234-56789abcdef4", "characteristicID": "12345678-1234-5678-1234-56789abcdef5" }, "write": { "serviceID": "12345678-1234-5678-1234-56789abcdef4", "characteristicID": "12345678-1234-5678-1234-56789abcdef6" } } } } } } } } Figure 3: Example property mapping 4. Usage A protocol map MAY be provided as part of the SDF model, specifically in the SDF affordance definition. The extension points in the SDF affordance definition defined in [I-D.ietf-asdf-sdf] are used to specify the protocol mapping information as a part of the SDF model. For SDF properties, the protocol mapping is specified as an extension to a named property quality using the sdfProtocolMap keyword. For SDF actions and events, the protocol mapping can be specified as an extension to the named quality or as part of the sdfInputData or sdfOutputData objects. 5. Examples Mohan, et al. Expires 24 July 2026 [Page 6] Internet-Draft sdf-protocol-mapping January 2026 5.1. BLE Protocol Mapping The BLE protocol mapping allows SDF models to specify how properties, actions, and events should be accessed using Bluetooth Low Energy (BLE) protocol. The mapping includes details such as service IDs and characteristic IDs that are used to access the corresponding SDF affordances. 5.1.1. BLE Protocol Mapping Structure For SDF properties and actions, the BLE protocol mapping structure is defined as follows: $$SDF-PROTOCOL-MAP //= ( ble: ble-protocol-map ) ble-protocol-map = { ? ble-property, ? read: { ble-property }, ? write: { ble-property } } ble-property = ( serviceID: text, characteristicID: text ) Figure 4: CDDL definition for BLE Protocol Mapping for properties and actions Where: * serviceID is the BLE service ID that corresponds to the SDF property or action. * characteristicID is the BLE characteristic ID that corresponds to the SDF property or action. For example, a BLE protocol mapping for a temperature property might look like: Mohan, et al. Expires 24 July 2026 [Page 7] Internet-Draft sdf-protocol-mapping January 2026 { "sdfProperty": { "temperature": { "sdfProtocolMap": { "ble": { "serviceID": "12345678-1234-5678-1234-56789abcdef4", "characteristicID": "12345678-1234-5678-1234-56789abcdef5" } } } } } For a temperature property that has different mappings for read and write operations, the BLE protocol mapping might look like: { "sdfProperty": { "temperature": { "sdfProtocolMap": { "ble": { "read": { "serviceID": "12345678-1234-5678-1234-56789abcdef4", "characteristicID": "12345678-1234-5678-1234-56789abcdef5" }, "write": { "serviceID": "12345678-1234-5678-1234-56789abcdef4", "characteristicID": "12345678-1234-5678-1234-56789abcdef6" } } } } } } For SDF events, the BLE protocol mapping structure is similar, but it may include additional attributes such as the type of the event. $$SDF-PROTOCOL-MAP //= ( ble: ble-event-map ) ble-event-map = { type: "gatt" / "advertisements" / "connection_events", ? serviceID: text, ? characteristicID: text } Mohan, et al. Expires 24 July 2026 [Page 8] Internet-Draft sdf-protocol-mapping January 2026 Figure 5: BLE Protocol Mapping for events Where: * type specifies the type of BLE event, such as "gatt" for GATT events, "advertisements" for advertisement events, or "connection_events" for connection-related events. * serviceID and characteristicID are optional attributes that are specified if the type is "gatt". For example, a BLE event mapping for a heart rate measurement event might look like: { "sdfEvent": { "heartRate": { "sdfOutputData": { "sdfProtocolMap": { "ble": { "type": "gatt", "serviceID": "12345678-1234-5678-1234-56789abcdef4", "characteristicID": "12345678-1234-5678-1234-56789abcdef5" } } } } } } Another example of an isPresent event using BLE advertisements: { "sdfEvent": { "isPresent": { "sdfOutputData": { "sdfProtocolMap": { "ble": { "type": "advertisements" } } } } } } Mohan, et al. Expires 24 July 2026 [Page 9] Internet-Draft sdf-protocol-mapping January 2026 5.2. Zigbee Protocol Mapping The Zigbee protocol mapping allows SDF models to specify how properties, actions, and events should be accessed using the Zigbee protocol. The mapping includes details such as cluster IDs and attribute IDs that are used to access the corresponding SDF affordances. 5.2.1. Zigbee Protocol Mapping Structure For SDF properties and events, the Zigbee protocol mapping structure is defined as follows: $$SDF-PROTOCOL-MAP //= ( zigbee: zigbee-protocol-map ) zigbee-protocol-map = { ? zigbee-property, ? read: { zigbee-property }, ? write: { zigbee-property } } zigbee-property = ( endpointID: uint, manufacturerCode: uint, clusterID: uint, attributeID: uint, type: uint ) Figure 6: CDDL definition for Zigbee Protocol Mapping for properties and actions Where: * endpointID is the Zigbee endpoint ID that corresponds to the SDF affordance. * clusterID is the Zigbee cluster ID that corresponds to the SDF affordance. * attributeID is the Zigbee attribute ID that corresponds to the SDF affordance. * type is the Zigbee data type of the attribute. Mohan, et al. Expires 24 July 2026 [Page 10] Internet-Draft sdf-protocol-mapping January 2026 SDF properties are mapped to Zigbee cluster attributes and events are mapped to Zigbee cluster attribute reporting. For example, a Zigbee protocol mapping for a temperature property might look like: { "sdfProperty": { "temperature": { "sdfProtocolMap": { "zigbee": { "endpointID": 1, "clusterID": 1026, // 0x0402 "attributeID": 0, // 0x0000 "type": 41 // 0x29 } } } } } SDF actions are mapped to Zigbee cluster commands. The Zigbee protocol mapping structure for actions is defined as follows: $$SDF-PROTOCOL-MAP //= ( zigbee: zigbee-action-map ) zigbee-action-map = { endpointID: uint, manufacturerCode: uint, clusterID: uint, commandID: uint, } Figure 7: CDDL definition for Zigbee Protocol Mapping for actions Where: * endpointID is the Zigbee endpoint ID that corresponds to the SDF action. * clusterID is the Zigbee cluster ID that corresponds to the SDF action. * commandID is the Zigbee command ID that corresponds to the SDF action. Mohan, et al. Expires 24 July 2026 [Page 11] Internet-Draft sdf-protocol-mapping January 2026 For example, a Zigbee protocol mapping to set a temperature might look like: { "sdfAction": { "setTemperature": { "sdfProtocolMap": { "zigbee": { "endpointID": 1, "clusterID": 1026, // 0x0402 "commandID": 0 // 0x0000 } } } } } 6. SCIM SDF Extension While SDF provides a way to describe a device, a method is needed to associate a mapping between an instance of a device and its associated SDF models. To accomplish this, we define a SCIM extension that can be used in conjunction with [I-D.ietf-scim-device-model] in Figure 8. Implementation of this SCIM extension is OPTIONAL and independent of the protocol mapping functionality defined in the rest of this document. The SCIM schema attributes used here are described in Section 7 of [RFC7643]. Mohan, et al. Expires 24 July 2026 [Page 12] Internet-Draft sdf-protocol-mapping January 2026 =============== NOTE: '\' line wrapping per RFC 8792 ================ { "id": "urn:ietf:params:scim:schemas:extension:sdf:2.0:Device", "name": "SDFExtension", "description": "Device extension schema for SDF.", "attributes": [ { "name": "sdf", "type": "string", "description": "SDF models supported by the device.", "multiValued": true, "required": true, "caseExact": true, "mutability": "readWrite", "returned": "default", "uniqueness": "none" } ], "meta": { "resourceType": "Schema", "location": "/v2/Schemas/urn:ietf:params:scim:schemas:extens\ ion:sdf:2.0:Device" } } Figure 8: SCIM SDF Extension Schema An example SCIM device schema extension might look like: { "schemas": [ "urn:ietf:params:scim:schemas:core:2.0:Device", "urn:ietf:params:scim:schemas:extension:sdf:2.0:Device" ], "id": "e9e30dba-f08f-4109-8486-d5c6a3316111", "displayName": "Heart Monitor", "active": true, "urn:ietf:params:scim:schemas:extension:sdf:2.0:Device": { "sdf": [ "https://example.com/thermometer#/sdfThing/thermometer", "https://example.com/heartrate#/sdfObject/healthsensor" ] } } Mohan, et al. Expires 24 July 2026 [Page 13] Internet-Draft sdf-protocol-mapping January 2026 7. Security Considerations The security considerations of [I-D.ietf-asdf-sdf] apply to this document as well. Each protocol mapped using this mechanism has its own security model. The protocol mapping mechanism defined in this document does not provide additional security beyond what is offered by the underlying protocols. Implementations MUST ensure that appropriate protocol- level security mechanisms are employed when accessing affordances through the mapped protocol operations. 8. IANA Considerations This section provides guidance to the Internet Assigned Numbers Authority (IANA) regarding registration of values related to this document, in accordance with [RFC8126]. 8.1. Protocol Mapping IANA is requested to create a new registry called "SDF Protocol Mapping". The registry must contain the following attributes: * Protocol map name * Protocol name * Description * Reference of the specification describing the protocol mapping. This specification must be reviewed by an expert. The registrant of an existing entry may request updates to that entry, subject to the same expert review. They should verify that updates preserve backward compatibility with deployed implementations, or if breaking changes are necessary, consider whether a new registry entry is more appropriate. Following protocol mappings are described in this document: Mohan, et al. Expires 24 July 2026 [Page 14] Internet-Draft sdf-protocol-mapping January 2026 +==============+===============+====================+===========+ | Protocol map | Protocol Name | Description | Reference | +==============+===============+====================+===========+ | ble | Bluetooth Low | Protocol mapping | This | | | Energy (BLE) | for BLE devices | document | +--------------+---------------+--------------------+-----------+ | zigbee | Zigbee | Protocol mapping | This | | | | for Zigbee devices | document | +--------------+---------------+--------------------+-----------+ Table 2: Protocol Mapping Registry 8.2. SCIM Device Schema SDF Extension IANA is requested to create the following extensions in the SCIM Server-Related Schema URIs registry as described in Section 6: +=======================+=============+==========+===========+ | URN | Description | Resource | Reference | | | | Type | | +=======================+=============+==========+===========+ | urn:ietf:params:scim: | SDF | Device | This | | schemas:extension: | Extension | | memo, | | sdf:2.0:Device | | | Section 6 | +-----------------------+-------------+----------+-----------+ Table 3 9. References 9.1. Normative References [I-D.ietf-asdf-sdf] Koster, M., Bormann, C., and A. Keränen, "Semantic Definition Format (SDF) for Data and Interactions of Things", Work in Progress, Internet-Draft, draft-ietf- asdf-sdf-25, 13 October 2025, . [I-D.ietf-scim-device-model] Shahzad, M., Iqbal, H., and E. Lear, "Device Schema Extensions to the SCIM model", Work in Progress, Internet- Draft, draft-ietf-scim-device-model-18, 3 September 2025, . Mohan, et al. Expires 24 July 2026 [Page 15] Internet-Draft sdf-protocol-mapping January 2026 [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, . [RFC7643] Hunt, P., Ed., Grizzle, K., Wahlstroem, E., and C. Mortimore, "System for Cross-domain Identity Management: Core Schema", RFC 7643, DOI 10.17487/RFC7643, September 2015, . [RFC8126] Cotton, M., Leiba, B., and T. Narten, "Guidelines for Writing an IANA Considerations Section in RFCs", BCP 26, RFC 8126, DOI 10.17487/RFC8126, June 2017, . [RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, May 2017, . 9.2. Informative References [BLE53] Bluetooth SIG, "Bluetooth Core Specification Version 5.3", 13 July 2021, . [RFC2616] Fielding, R., Gettys, J., Mogul, J., Frystyk, H., Masinter, L., Leach, P., and T. Berners-Lee, "Hypertext Transfer Protocol -- HTTP/1.1", RFC 2616, DOI 10.17487/RFC2616, June 1999, . [RFC7252] Shelby, Z., Hartke, K., and C. Bormann, "The Constrained Application Protocol (CoAP)", RFC 7252, DOI 10.17487/RFC7252, June 2014, . [Zigbee22] Zigbee Alliance, "Zigbee 3.0 Specification", 2022, . Appendix A. CDDL Definition This appendix contains the combined CDDL definitions for the SDF protocol mappings. Mohan, et al. Expires 24 July 2026 [Page 16] Internet-Draft sdf-protocol-mapping January 2026 file "sdf-protocol-map.cddl" $$SDF-EXTENSION-DATA //= ( sdfProtocolMap: { * $$SDF-PROTOCOL-MAP } ) $$SDF-PROTOCOL-MAP //= ( ble: ble-protocol-map ) ble-protocol-map = { ? ble-property, ? read: { ble-property }, ? write: { ble-property } } ble-property = ( serviceID: text, characteristicID: text ) $$SDF-PROTOCOL-MAP //= ( ble: ble-event-map ) ble-event-map = { type: "gatt" / "advertisements" / "connection_events", ? serviceID: text, ? characteristicID: text } $$SDF-PROTOCOL-MAP //= ( zigbee: zigbee-protocol-map ) zigbee-protocol-map = { ? zigbee-property, ? read: { zigbee-property }, ? write: { zigbee-property } } zigbee-property = ( endpointID: uint, manufacturerCode: uint, clusterID: uint, attributeID: uint, type: uint Mohan, et al. Expires 24 July 2026 [Page 17] Internet-Draft sdf-protocol-mapping January 2026 ) $$SDF-PROTOCOL-MAP //= ( zigbee: zigbee-action-map ) zigbee-action-map = { endpointID: uint, manufacturerCode: uint, clusterID: uint, commandID: uint, } Appendix B. OpenAPI Definition The following non-normative model is provided for convenience of the implementor. Mohan, et al. Expires 24 July 2026 [Page 18] Internet-Draft sdf-protocol-mapping January 2026 file "ProtocolMap.yaml" =============== NOTE: '\' line wrapping per RFC 8792 ================ openapi: 3.0.3 info: title: SDF Protocol Mapping description: |- SDF Protocol Mapping. When adding a new protocol mapping please add a reference to the protocol map for all the schemas in this file. version: 0.10.0 externalDocs: description: SDF Protocol Mapping IETF draft url: https://datatracker.ietf.org/doc/draft-ietf-asdf-sdf-protocol\ -mapping/ paths: {} components: schemas: ## Protocol Map for a property ProtocolMap-Property: type: object properties: sdfProtocolMap: oneOf: - $ref: './ProtocolMap-BLE.yaml#/components/schemas/Prot\ ocolMap-BLE-Propmap' - $ref: './ProtocolMap-Zigbee.yaml#/components/schemas/P\ rotocolMap-Zigbee-Propmap' ## Protocol Map for an event ProtocolMap-Event: type: object properties: sdfProtocolMap: oneOf: - $ref: './ProtocolMap-BLE.yaml#/components/schemas/Prot\ ocolMap-BLE-Event' - $ref: './ProtocolMap-Zigbee.yaml#/components/schemas/P\ rotocolMap-Zigbee-Event' Figure 9 B.1. Protocol map for BLE Mohan, et al. Expires 24 July 2026 [Page 19] Internet-Draft sdf-protocol-mapping January 2026 file "ProtocolMap-BLE.yaml" =============== NOTE: '\' line wrapping per RFC 8792 ================ openapi: 3.0.3 info: title: SDF Protocol Mapping for BLE description: |- SDF Protocol Mapping for BLE devices. version: 0.10.0 externalDocs: description: SDF Protocol Mapping IETF draft url: https://datatracker.ietf.org/doc/draft-ietf-asdf-sdf-protocol\ -mapping/ paths: {} components: schemas: ## Protocol Mapping for BLE Property ProtocolMap-BLE-Propmap: required: - ble type: object properties: ble: required: - serviceID - characteristicID type: object properties: serviceID: type: string format: uuid example: 00001809-0000-1000-8000-00805f9b34fb characteristicID: type: string format: uuid example: 00002a1c-0000-1000-8000-00805f9b34fb ## Defines different types of BLE events ProtocolMap-BLE-Event: required: - ble type: object properties: ble: required: - type Mohan, et al. Expires 24 July 2026 [Page 20] Internet-Draft sdf-protocol-mapping January 2026 type: object properties: type: type: string example: gatt enum: - gatt - connection_events - advertisements serviceID: type: string example: 00001809-0000-1000-8000-00805f9b34fb characteristicID: type: string example: 00002a1c-0000-1000-8000-00805f9b34fb Figure 10 B.2. Protocol map for Zigbee file "ProtocolMap-Zigbee.yaml" =============== NOTE: '\' line wrapping per RFC 8792 ================ openapi: 3.0.3 info: title: SDF Protocol Mapping for Zigbee description: |- SDF Protocol Mapping for Zigbee devices. version: 0.10.0 externalDocs: description: SDF Protocol Mapping IETF draft url: https://datatracker.ietf.org/doc/draft-ietf-asdf-sdf-protocol\ -mapping/ paths: {} components: schemas: ## Protocol mapping for Zigbee property ProtocolMap-Zigbee-Propmap: required: - zigbee type: object properties: zigbee: required: - endpointID Mohan, et al. Expires 24 July 2026 [Page 21] Internet-Draft sdf-protocol-mapping January 2026 - clusterID - attributeID type: object properties: endpointID: type: integer format: int32 example: 1 clusterID: type: integer format: int32 example: 6 attributeID: type: integer format: int32 example: 16 type: type: integer format: int32 example: 1 ProtocolMap-Zigbee-Event: allOf: - $ref: '#/components/schemas/ProtocolMap-Zigbee-Propmap' Figure 11 Acknowledgments TODO acknowledge. Authors' Addresses Rohit Mohan Cisco Systems 170 West Tasman Drive San Jose, 95134 United States of America Email: rohitmo@cisco.com Bart Brinckman Cisco Systems 170 West Tasman Drive San Jose, 95134 United States of America Email: bbrinckm@cisco.com Mohan, et al. Expires 24 July 2026 [Page 22] Internet-Draft sdf-protocol-mapping January 2026 Lorenzo Corneo Ericsson Hirsalantie 11 FI-1296 Jorvas Finland Email: lorenzo.corneo@ericsson.com Mohan, et al. Expires 24 July 2026 [Page 23]